Parts for Ge ZIPS360NHCSS: Controls & Components Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

This oven grill vent directs heat and exhaust away from the control area and helps protect internal components while allowing proper airflow for safe operation. It restores the oven's ventilation and exterior appearance. What it does:

• Directs hot air and exhaust from the oven cavity to the exterior vent path
• Helps prevent heat damage to nearby controls and trim
• Maintains proper airflow to support consistent oven performance
• Covers and protects internal vent openings from debris and splashes

• Disconnect power to the appliance before attempting any service.
• Typically fastens with a few screws; keep screws and trim pieces for reassembly.
• Handle edges carefully to avoid cuts and to prevent scratching the finish.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

This blower fan duct channels air moved by the evaporator fan through the refrigerator's air passages, helping maintain consistent temperatures and reliable cooling performance. Replacing a cracked or warped duct restores the designed airflow path and reduces fan noise. What it does:

• Directs airflow from the evaporator fan to the cooling vents for proper circulation
• Helps balance temperatures between compartments for even cooling
• A damaged or misaligned duct can cause weak airflow, warm spots, frost/ice around the cover, or unusual fan noise
• Restores correct air routing after breakage or warping

• Disconnect power before servicing to avoid electrical shock or moving-fan injury
• Remove shelves/drawers and the interior cover as needed to access the duct; retain screws and clips
• Transfer any reusable seals or hardware from the original duct to the new part
• After reassembly, ensure the fan spins freely and no rubbing noises are present before returning to service

Seals the fan housing to direct airflow and reduce vibration. Replace if you notice uneven cooling or increased noise. Confirm fit with your model number.

LED light board assembly that restores interior refrigerator illumination when lights fail or dim. Replace when experiencing uneven lighting or dark areas. Verify fit with your refrigerator model number before ordering.

Replace your refrigerator's LED light lens cover when cracked, yellowed, or missing. This clear plastic cover protects the LED module and diffuses light.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

If your refrigerator compartment isn't cooling while the freezer stays cold, the evaporator fan motor likely failed. DIY-friendly repair with video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Mounting bracket that secures the damper assembly inside your refrigerator. Replace if cracked, broken, or missing to properly support the damper component.

This drain fan assembly circulates air around the refrigerator's drain/evaporation area so defrost water can dry properly. Replacing a worn or seized fan restores intended airflow and helps reduce lingering moisture and related odors. What it does:

• Moves air across the drain/evaporation path to aid drying after defrost cycles
• Helps minimize standing water and musty odors near the drain pan area
• Supports proper moisture management in the machine compartment
• Common symptoms of a failing fan include not running, intermittent operation, rattling/squealing, or occasional water pooling near the base

• One drain fan assembly

• Disconnect power before servicing; wear cut-resistant gloves
• Location and access vary by model—refer to your model's service information
• Note wire connections and mounting orientation before removal; transfer any reusable hardware from the original assembly
• After installation, ensure the blade spins freely and wiring is routed clear of moving parts

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Refrigerator not cooling or freezer has excessive frost buildup? This evaporator defrost assembly heats the coil to eliminate ice. Moderate DIY repair.

Fix fresh food section freezing or not cooling issues with this air damper assembly. Controls airflow between freezer and refrigerator compartments.

Left-side evaporator baffle directs cold air flow in the freezer compartment. Replaces cracked, broken, or missing baffles to restore proper airflow.

Collects defrost water under your refrigerator. Replace if cracked, leaking, or missing to prevent water damage and moisture buildup on your floor.