Parts for Ge JSS86SP4SS: Cooktop Parts

Indicator light illuminates when cooktop surface is hot. Replace if light stays on constantly, fails to light, or housing is cracked. Verify fit by model.

Replacement glass assembly that forms the cooktop surface of your electric range. Needed when the original glass is cracked, chipped, or shattered.

Burner not heating? This 5.5" radiant element fits beneath glass cooktops. Common fix for non-working burners. Moderate DIY, 20-30 minutes to replace.

This lower oven warming element heats the oven's warming/holding compartment so food stays warm until serving. Replaces a damaged or non-heating lower element to restore consistent low-temperature operation. What it does:

• Heats the oven's warming/lower compartment for holding cooked food
• Replaces elements that show visible damage, burn-through, or no heat output
• Helps restore even low-temperature performance when the warmer function fails
• Works with the oven's temperature control and safety circuits to provide steady heat

• One lower oven warming element

• Disconnect power at the breaker before beginning any repair
• Wear gloves; element edges and terminals may be sharp
• Verify proper wiring and secure terminal connections during installation

Burner stopped working or won't heat properly? This dual radiant surface element restores full cooking function. DIY-friendly repair, typically 30 minutes.

Element stopped heating or center coil went out? This radiant heating element restores even stovetop cooking. DIY repair in 20 minutes with basic tools.

The Radiant Element Spring is an OEM part for GE electric ranges. This spring supports the radiant element coil and provides the necessary tension to allow the coil to glow red-hot during the cooking process.

Causes of a bad spring can include fatigue from repeated heating and cooling cycles, damage due to impact or mishandling, or corrosion over extended use.

Symptoms of a bad radiant element spring include:

• Radiant element coil sagging or not sitting flush
• Element coil not heating properly or heating unevenly
• Excessive heat and energy use from a misaligned coil
• Element mounting brackets becoming loose over time

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix loose or damaged heating elements with this radiant element bracket. Secures the element to your range for safe operation. Simple repair.

This metal mounting bracket secures a radiant heating element to the cooktop so the element stays aligned and stable during use. It restores proper fit and reduces movement that can cause intermittent contact or uneven heating. What it does:

• Holds the radiant heating element in place to prevent movement or sagging
• Keeps electrical contacts aligned to reduce arcing, flicker, or intermittent heating
• Helps maintain even heat distribution by stabilizing element position
• Replaces a bent, broken, or missing bracket that allows the element to shift

• Disconnect power at the breaker before servicing the cooktop to avoid shock
• Handle the glass cooktop and element carefully to avoid cracking or injury
• Verify correct bracket orientation and mounting location before tightening hardware
• Use basic hand tools; if the element or wiring is damaged, replace those parts.

Cable clip for electric ranges. Secures and organizes wiring inside the control area. Replace if clip is broken, cracked, or missing to keep cables tidy.

Replacement cable clip that secures wiring harnesses to your range cabinet or chassis. Needed when original clip is broken, cracked, or missing.

The Rear Vent Trim and Gasket Assembly is an OEM part for GE ranges. It seals the rear vent opening of the range, directing hot air and potential gas fumes outside through the exhaust vent during oven use. Without an intact seal provided by the gasket and vent trim, combustion byproducts can enter the kitchen presenting safety and performance issues.

Causes of a bad range rear vent assembly include wear over years of use with high heat cycles, cracking or degradation of sealing materials, or damage from cleaning or impacts around the vent area.

Symptoms of an issue include:

• Foul odors detected in the kitchen during use of the oven
• Inefficient or uneven baking and broiling
• Visible openings or gaps seen around the rear vent perimeter
• Detached, cracked, or missing components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.