Divider Or Deflector

The Door Mullion is an OEM part for GE refrigerators. It is a vertical component that separates the fresh food and freezer compartments, while allowing for the seal and closure of the refrigerator doors.

Causes of a bad door mullion may include physical damage from impact or mishandling, wear and tear over time, or compatibility issues with the specific refrigerator model.

Symptoms that may indicate a need to replace the door mullion include:

• Air leaks or drafts between the fresh food and freezer compartments
• Difficulty in closing or sealing the refrigerator doors properly
• Visible cracks, breaks, or damage to the mullion itself
• Condensation or frost buildup around the mullion area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

White vertical strip that seals between French doors on your refrigerator. Replace if cracked, broken, or worn from impact or regular use.

Ice scattering everywhere? This deflector guides cubes or crushed ice down the chute into your glass. Replaces cracked or missing deflectors in 30 minutes.

The Drawer Guide is an OEM part for LG refrigerators. This part allows the smooth and effortless operation of the refrigerator's drawers, ensuring they glide in and out with ease. 

Causes of a bad drawer guide can be attributed to wear and tear over time, misalignment during installation, or damage from excessive force or improper use of the drawers.

Symptoms of a bad drawer guide include:

• Difficulty opening or closing the drawers
• Drawers getting stuck or not sliding properly
• Excessive friction or resistance when operating the drawers
• Drawers becoming misaligned or tilted
• Unusual noises or grinding sounds when using the drawers

This OEM LG part is also compatible with some Kenmore models.

Vertical flipper mullion assembly mounts to fresh-food door and pivots to seal center gap between French doors. Replace if cracked, broken, or rusting.

Replaces broken or cracked divider guide components in your refrigerator freezer. Restores smooth sliding and secure positioning of adjustable dividers.

This mullion assembly forms the front center divider of the refrigerator and includes an integrated anti-sweat heater. It helps keep the area where the door gaskets meet dry, supporting a clean look and a reliable, moisture-free seal.

• Provides the rigid center divider that the door gaskets seal against
• Built-in heater warms the divider to reduce sweating/condensation in humid conditions
• Helps limit air leaks that can lead to moisture, frost, or temperature fluctuations
• Common signs of trouble: persistent condensation on the center divider, visible cracks/warping, or poor gasket contact along the center

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Remove mounting fasteners, carefully release the assembly, and disconnect the wire harness (note routing/orientation)
• Position the new assembly, reconnect the harness securely, and reinstall fasteners without overtightening
• Verify doors close smoothly and gaskets contact evenly along the divider before restoring power

This is the flip-out center rail for French-door refrigerators. It closes the gap between the fresh food doors to maintain a tight seal, helping keep cold air in and moisture out for consistent cooling. What it does

• Flips into place when both doors close to complete the perimeter seal
• Helps prevent warm-air leaks and condensation between the doors
• Supports proper temperature by reducing air infiltration
• Common symptoms: loose or broken flipper, doors not staying closed, moisture or frost at the center seam

• Includes 1 door mullion (flipper) assembly

• Disconnect power before servicing and clear items from door bins
• Open the doors and carefully release any retaining screws/clips; design varies by model
• Note spring orientation/hinge engagement and transfer any trim as needed
• Ensure the flipper moves freely and snaps closed before restoring power

This diverter valve directs wash water inside the machine, switching flow between internal paths during wash and drain/recirculation steps. Replacing a failed diverter restores proper water routing so cycles advance and complete as designed.

• Redirects water between the drain and recirculation/spray paths as commanded by the control
• Ensures correct water flow for wash, rinse, and drain steps
• A sticking or failed diverter can cause slow/no drain or no recirculation/spray
• May lead to cycle pauses/errors, unusual clicking/buzzing from the valve area, or leaks at the valve body/ports

• Unplug the washer and turn off water supply; expect residual water in hoses
• Access location varies by model; typically mounted along the pump/hoses under the cabinet
• Move hoses/clamps and the electrical connector one at a time; match port orientation
• After installation, run a rinse/drain test and check all connections for leaks

This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.

• Guides the icemaker fill stream into the fill cup/funnel during the fill cycle
• Diverts stray or excess water to the overflow path to reduce spills
• Helps prevent leaks, sheets of ice, and clumped cubes under the icemaker
• Clues it may be needed: cracked, warped, or missing guide; water dripping from the fill area

• Disconnect power and turn off the water supply before servicing
• Remove ice bin and any covers to access the icemaker fill area
• Unclip/unscrew the old diverter; align and secure the new part to the fill cup/tube
• Restore water and power; run a test fill and check for leaks

Directs airflow from evaporator through the fresh food compartment. Replace if cracked, broken, or missing to restore proper air distribution.

Ice spilling inside freezer or dispenser not working? This ice container deflector guides cubes into the chute. Simple snap-in installation fix.

Plastic retaining clip that secures drawer divider modules in place. Replaces broken, cracked, or missing snuggers to restore proper fit and separation.

Replacement diverter overflow that helps channel excess water away from the ice maker/water system to reduce pooling and leaks. Restores proper drainage so the refrigerator interior stays dry and operates as intended. What it does:

• Directs overflow or stray water from the ice maker/water area into the drain path
• Helps prevent water pooling or dripping inside the freezer or cabinet
• Use when you notice leaks, water pooling under shelves, or water coming from the dispenser/ice area

• Always disconnect power and shut off the water supply before starting any repair
• Removal of interior shelves/trim or access panels may be required to reach the diverter
• Handle plastic tabs and clips carefully to avoid breakage; replace any damaged fasteners

Molded plastic deflector that directs airflow inside your refrigerator. Replace if cracked, warped, or missing to restore proper air circulation.

This mullion rail installs between refrigerator compartments to create a tight seal when the door closes. Replace if cracked, broken, or no longer sealing properly.