Parts for Kenmore 790.97413411 (79097413411, 790 97413411): Doors Parts

Oven won't maintain temperature or exterior gets too hot? This insulation blanket contains heat and protects nearby components. Moderate DIY repair.

This interior cabinet liner replaces a damaged or cracked refrigerator cabinet panel to restore a clean, sealed interior surface and proper mounting for shelves or components. It helps maintain interior hygiene and prevents airflow leaks. What it does

• Provides the finished interior surface for the refrigerator cabinet and supports shelf and accessory mounting.
• Covers and protects insulation and internal cavity areas from spills, stains, and physical damage.
• Helps maintain proper airflow paths and compartment sealing to support cooling performance.
• Commonly replaced when the liner is cracked, warped, damaged by impact, or permanently stained.

• One interior cabinet liner panel as shown.

• Liners may require panel clips, screws, or adhesive (verify retained fasteners).
• Disconnect power and empty the compartment before starting to avoid injury or damage.
• Handle carefully to avoid cracking or scratching the replacement liner during installation.
• Reuse or replace any trim, clips, or fasteners only if they are present and in good condition.

Replacement screw for securing panels, brackets, and covers on appliances. Replaces missing, stripped, or damaged screws to restore alignment.

This door assembly replaces a damaged or dented outer refrigerator door to restore a clean exterior and proper sealing. It provides the structural panel and mounting points needed for door hardware and trim. What it does:

• Replaces a bent, cracked, or cosmetically damaged outer refrigerator door panel
• Restores proper alignment for door handles, hinges, and trim pieces
• Helps maintain correct door closure to protect internal temperatures
• Stops drafts and visible damage that can lead to moisture buildup or further wear

• Handle, hinge screws, and trim may need transfer from original door
• Disconnect power to the appliance and remove food before working on doors
• Support the door during removal/installation to avoid damage or injury

This spacer positions and cushions refrigerator components to prevent contact and reduce vibration, helping panels and assemblies align correctly for reliable operation. Lightweight and simple to install, it restores proper fit where the original spacer is damaged or missing. What it does:

• Keeps panels, trim, or internal components spaced correctly to maintain alignment
• Absorbs minor vibration and prevents metal-to-metal contact that can cause noise
• Helps preserve seals and door alignment by maintaining correct component clearance
• Common symptom: loose trim, rubbing panels, rattling, or visible gap where a spacer is missing

• One spacer

• Disconnect power to the appliance before beginning any work
• Remove adjacent panels or trim as needed to access the spacer; retain fasteners for reassembly
• Inspect surrounding clips or mounting points and replace any damaged hardware

This replacement door hinge restores smooth pivoting and proper alignment so the appliance door opens and closes correctly. It helps stop sagging, misalignment, rubbing and uneven sealing. What it does

• Provides the pivot point that lets the door swing open and closed.
• Replaces a worn, bent or broken hinge causing a sagging or drooping door.
• Helps restore a tight door seal to prevent cool-air loss and uneven temperatures.
• Eliminates clicking, binding or scraping noises caused by a damaged hinge.

• Support the door before removing the old hinge to prevent dropping or damage.
• Use basic hand tools; keep fasteners and any spacers for reassembly.
• Check door alignment and seal after installation; adjust hinge position as needed.

Mounting spacer positions and supports range components for proper alignment. Replace if worn, cracked, or missing to restore correct panel fit.

A genuine replacement refrigerator door handle that restores a secure grip and reliable opening on compatible units. Designed to match the original fit and finish so you can use the door normally again. What it does:

• Replaces a broken, cracked or missing refrigerator door handle
• Provides a solid grip for opening and closing the door smoothly
• Restores proper alignment and appearance of the door front
• Helps prevent further damage from improvised grips or taped-on handles

• One replacement refrigerator door handle

• Basic hand tools typically required; follow the OEM instructions for fastener locations
• Work carefully to avoid scratching the door finish and to retain any mounting clips or screws
• If the handle is near electrical components, unplug the appliance or disconnect power before starting

Metal support bracket that secures and stabilizes range components. Replaces broken, bent, or missing brackets to restore proper panel alignment.

Replaces cracked, broken, or missing trim on your range control panel. This decorative trim piece installs around the control area for a finished look.

Fastens panels, brackets, and covers inside your range or oven. Replace this screw if missing, stripped, or rusted to secure components properly.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.