Electrolux Range Hood Parts

Front console touch pad that houses control buttons and display for your range hood. Replace if cracked, broken, non-responsive, or display is damaged.

A replacement refrigerator water filter that helps reduce taste and odor issues and improves clarity of drinking water. Fits inline into the refrigerator's water/ice system to restore cleaner-tasting water. What it does:

• Filters impurities that can cause off taste or odor in dispenser water and ice
• Helps reduce visible particles and cloudiness in dispensed water
• Supports proper water flow for the dispenser and ice maker when functioning correctly
• Commonly replaced when water tastes bad, smells, or appears cloudy

• Replace with manufacturer-recommended filter and follow refrigerator-specific instructions
• Turn off the water supply and dispense water briefly to depressurize before removing the old filter
• After installation, flush several gallons of water per manufacturer guidance to clear air and loose carbon
• Dispose of the used filter according to local regulations; check for any refrigerator-specific priming steps

Fix no display, won't start, or intermittent power issues in your hood. This control board regulates voltage to restore reliable operation and startup.

Touch pad control panel for range hoods. Mounts on the underside of the vent hood. Replace if buttons are unresponsive, panel is cracked, or display is damaged.

Extension kit for range hoods. Adapts ductwork height for proper installation. Replaces missing or damaged extension components during setup.

Fix a hood that won't power on or has no lights with this transformer. This essential electrical component converts voltage to power your range hood.

This refrigerator water filter cartridge reduces common water tastes and odors and helps protect your ice and dispense lines. It's a direct-replacement cartridge designed for easy swap-out to restore clearer, better-tasting water. What it does:

• Filters out chlorine taste and odor for improved drinking water flavor
• Captures sediment and particulate to help keep ice and dispenser lines cleaner
• Helps maintain normal water flow and clear ice when operating properly
• Fits inline with your fridge's water system to provide filtered water on demand

• Replace the cartridge according to your refrigerator owner's manual or when water taste, odor, or flow declines
• Flush system after installation per manufacturer guidance to remove trapped air and loose carbon fines
• Turn off water supply or follow appliance-specific safety steps before removing the old filter

This blower assembly circulates air through the appliance to support proper airflow and heat distribution, restoring normal operation and efficiency when the original blower is damaged or failing. It replaces worn or broken blower components to reduce noise and improve performance. What it does:

• Spins the blower wheel to move air through the unit for proper heating, cooling, or venting
• Restores airflow when reduced air movement causes longer cycles or poor performance
• Reduces unusual noise from a wobbling or damaged blower wheel/housing
• Helps prevent overheating caused by restricted or ineffective air circulation

• Disconnect power (and gas if applicable) before starting any repair
• Access typically requires removing exterior panels or the front panel; use basic hand tools
• Inspect and clean surrounding airflow paths and vents of lint or debris while replacing the blower

This refrigerator water filter cartridge replaces a factory filter to help restore clearer, better-tasting water and ice. It's a direct-replacement cartridge designed for simple swap-out maintenance. What it does

• Filters tap water that serves the fridge dispenser and ice maker to improve taste and reduce sediment and chlorine-related odors.
• Helps prevent sediment and debris from reaching dispenser and ice components.
• Common signs you need this part: reduced water flow, noticeable change in water or ice taste, or filter-change indicator.

• One refrigerator water filter cartridge.

• Turn off the water supply and relieve dispenser pressure before removing the old filter.
• Follow the fridge maker's published instructions for removal and insertion; ensure the filter seats and locks fully.
• Flush several glasses of water after installation to clear trapped air and carbon fines.
• Check for leaks at the filter housing and connections before finishing.

Discharge collar for range hoods. Connects ductwork to the exhaust outlet. Replace if cracked, dented, or missing to ensure proper ventilation fit.

Replacement housing cover for range hoods. Installs as the exterior shell or casing. Needed when original is cracked, dented, discolored, or damaged.

Replacement canopy trim for range hoods. Covers the exterior housing for a finished appearance. Order when original is dented, scratched, or missing.

Decorative chimney cover that conceals the ductwork between your range hood and ceiling. Replace if cracked, dented, discolored, or missing.