Parts for Craftsman 247887050: Engine Parts

Snow thrower won't start when you pull the cord? A broken or loose starter handle prevents engine starting. Easy 10-minute fix for most models.

This replacement part is an engine, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This is a complete engine and is found in many different types of lawn mowers. The engine is arguable the most important part in and machine as it allows the entire appliance to operate. In many cases, the appliance is out of commission if the engine does not work.A new engine might be needed if the current one is not starting, or stops during use. If the user notices sounds or unfamiliar noises coming from inside the engine it might be time to replace it. There are many things that could be wrong inside the engine, be sure to check more specific parts to ensure that the entire engine needs to be replaced rather than only one smaller part. This is a genuine OEM part sourced directly from the manufacturer. This engine is sold individually.

Replace a leaking or damaged oil drain assembly on your snowblower engine. Includes valve for easier oil changes. Basic hand tools required.

Replace your engine's oil fill plug if it's cracked, stripped, or missing. This plug seals the oil fill opening on small engines for snowblowers and tillers.

Complete engine gasket kit for gas snow throwers. Replace when rebuilding engine or if you notice oil leaks. Verify fit with your model number.

External gasket kit seals carburetor and engine surfaces on lawn equipment. Replace when you notice fuel leaks or loss of compression. Verify fit with your model.

Engine losing power or running rough? A worn cylinder head assembly often causes reduced efficiency. This part covers the cylinder and houses valves.

Replacement oil drain plug for small engines on outdoor power equipment. Needed when original plug is stripped, cracked, or leaking. Installs at oil pan.

Ignition coil assembly for snow throwers and lawn engines. Installs on the engine block. Replace if your original coil is cracked, broken, or detached.

Flange bolt fastener for outdoor power equipment. Secures components throughout engine and chassis. Replace if stripped, corroded, or missing.

Stator for gas snow throwers. Mounts to the engine to generate power for lights or battery charging. Replace if cracked, damaged, or missing.

Replacement flywheel for small engines. This rotating wheel component stores rotational energy. Order a new one if yours is cracked, rusted, or damaged.

Fix engine overheating issues with this cooling fan. Keeps your small engine running at proper temperature. Direct replacement part for reliable operation.

Engine won't start or pull cord slips? This starter cup connects the recoil mechanism to start your engine. Simple bolt-on replacement part.

Fastener nut for outdoor power equipment. Secures components in place during operation. Replace if stripped, corroded, or missing to restore assembly.

M6 x 1 flange bolt for outdoor power equipment. Secures engine covers, handles, and components. Replace if stripped, rusted, or missing threads.

Protective shroud that covers the muffler assembly on your snow thrower. Replace this metal or plastic cover if cracked, broken, or missing.

Replacement muffler assembly for gas snowblowers and lawn engines. Installs on exhaust system. Order if your original is rusted, cracked, or damaged.

Engine valve cover cap for outdoor power equipment. Replaces cracked, broken, or missing valve covers on small engines. Direct fit for blowers, tillers, and more.

Engine running rough or making ticking noises? A worn rocker arm stud can affect valve timing. This replacement stud restores proper valve operation.

Fixes engine misfires and rough running caused by improper valve clearance. This adjusting nut helps restore correct valve timing on lawn mowers and tillers.

This replacement part is a stud assembly. This is a genuine replacement part made by MTD. This stud assembly is responsible for keeping the muffler in place and secure so that the lawn mower may operate smoothly and according to the user's preferences. A new stud assembly might be needed if the current one is misplaced or damaged. It is not unusual for the studs to become stripped over time and need to be replaced. If the muffler is no longer able to stay in place, it can be due to the studs and should be looked into. Be sure the engine is completely turned off before attempting to replace this part. This stud assembly is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

This replacement part is a stud, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. Studs are typically found in or around the carburetor in many lawn mowers. These studs hold specific parts in place and keep the engine running smoothly and efficiently. A new stud might be needed if the user notices that different parts of the carburetor are loose or even missing. It is possible that the previous studs become stripped or worn down over time due to normal wear and tear. It's possible that the stud can become stuck as well, and the user might need pliers to retrieve and replace it with a new part. This replacement part is sold individually and is a genuine OEM part sourced directly from the manufacturer. Be sure to purchase the correct amount of studs as many machines require more than one for proper operations.

Replaces a cracked, hardened, or broken primer bulb on gas-powered engines. Installs on the carburetor to inject fuel for priming before starting.

Carburetor assembly for snow throwers and small engines. Installs in the engine to mix air and fuel. Replace if cracked, clogged, or worn from use.

Choke push rod for snow thrower engines. Connects choke control to carburetor. Replace if bent, damaged, or missing for proper choke operation.

Engine won't start in cold weather? This choke bracket controls airflow to help start your snow thrower engine. Simple repair takes 15-20 minutes.

This genuine replacement part is an air filter heating cover for snowblowers. The air filter heating pipe cover is the plastic piece that covers the heating pipe of a snowblower. This cover is meant to protect the user from burning themselves on the heating pipe while using the machine. If the heating pipe cover is damaged to the point where it is no longer covering the heating pipe, it should be replaced. Thankfully, replacing this part is a simple process.To replace the heating pipe cover, locate the mounting screws that secure it to the snowblower. Before removing, make sure the engine has cooled to avoid getting burned. Once located, remove the mounting screws that attach the cover. Once removed, replace with the new cover and fasten the screws tightly. This OEM replacement part is sold individually and is compatible with MTD brand snowblowers.

Snowblower won't start or shuts off unexpectedly? This ignition switch controls engine power. Direct replacement part restores reliable starting.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

Replace your snowblower's cracked or broken air cleaner housing. This protective cover encloses the air filter element and mounts to the carburetor.

Carburetor choke knob for snow thrower engines. Replaces cracked, broken, or missing choke control knobs. Installs on the carburetor assembly.

Engine runs too fast or won't maintain steady speed? This governor bracket controls engine RPM. Common repair for speed control issues on small engines.

Fix engine surging or racing issues with this throttle spring. Closes the throttle valve to control fuel flow. Quick DIY fix for stuck throttles.

The governor rod is a genuine replacement part found on select models of snowblowers. This rod is responsible for connecting the throttle cable and throttle body, helping to open and close the throttle to change the speed of the engine. This durable metal rod is exposed to repetitive motion and constant vibrations, which can cause damage or wear over time. If this rod does not function, the throttle will be unable to be controlled and that can affect the use of the equipment. Replacing the governor rod with this genuine part will guarantee an exact fit for compatible units. This genuine governor rod is manufactured to specific OEM standards and can be used in compatible machines from Cub Cadet, MTD, Yard Man, Craftsman, Troy-Bilt, Yard Machines, and HUSKEE. The part can be found in snowblowers, with hundreds of possible models that can take this governor's rod. It is made of durable metal and sold as an individual unit. No additional components or hardware are included, and any additional parts will require a separate purchase. Always wear gloves and perform engine repairs only when the machine has had time to cool. Be sure to disengage the engine before doing any work for safety, as well.

If your snow thrower won't maintain consistent speed or the engine surges, the throttle control may need replacement. Moderate DIY repair in 30-45 minutes.

Throttle control knob for snow throwers and gas snowblowers. Replaces broken, cracked, or missing throttle knobs for smooth engine speed adjustment.

Snow thrower won't start or cranks slowly? This electric starter restores reliable starting in cold weather. Moderately difficult repair for most DIYers.

Replacement shield cover for blower housing. Installs over the blower assembly to protect internal components. Order a new cover if yours is cracked or missing.

Push rod kit for small engines. Installs in the valve train assembly. Replace if rods are bent, damaged, or worn from normal engine operation.

Can't check your oil level accurately? This dipstick assembly measures engine oil in hard-to-reach spaces. Simple DIY install for tillers and snow throwers.

Can't check your oil level accurately? This dipstick assembly measures engine oil in hard-to-reach spaces. Simple DIY install for tillers and snow throwers.

This is a genuine MTD fuel cap replacement made for use on select snowblowers. It features a molded gasket for secure sealing and less risk of losing parts. The fuel cap is responsible for securing the fuel in the fuel tank during operation so that it doesn't spill out. There is an air hole in the cap to prevent pressurization of the fuel, ensuring safe operation at all times. This cap is made of plastic and it can become cracked or stripped with regular use. If it is damaged, the fuel will not be secure and the machine will not be safe to use. That will require an immediate replacement. This OEM fuel cap is made to exact standards by MTD and is compatible with several models of snow blowers and snow throwers. It is also capable of fitting select models from Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. It features an easy plastic grip and a seal to prevent spillage. It can be installed with no tools and is sold as an individual unit. It is easy to screw the new cap into place, but be sure to thread the screw properly to prevent accidental stripping or misthreading that can cause the cap to get stuck.

Fuel filter for small engines on snowblowers, tillers, and lawn equipment. Replace annually or if engine runs rough to ensure clean fuel flow. Verify fit with your model number.

Complete fuel tank assembly for snow throwers and tillers. Includes tank and mounting hardware. Replace if cracked, leaking, or damaged during storage.

Fuel tank nipple connects fuel lines to the tank on small engines. Replace if cracked, leaking, or worn to restore proper fuel line connections.

Fuel line kit for small engines. Carries fuel through the machine. Replace if cracked, leaking, or ends don't fit securely even when clamped down.

Starter rope won't retract or engine won't crank? This recoil starter assembly includes housing, spring, pulley, rope and grip. Moderate DIY repair.

Replacement fastener nut for lawn and garden equipment. Threads onto bolts to secure parts together. Replace if stripped, corroded, or missing.

Engine won't start after sudden stop? A sheared flywheel key breaks the connection between crankshaft and flywheel. Simple DIY repair.

Engine mounting stud for snow throwers and lawn equipment. Secures engine components together. Replace if broken, stripped, or missing threads.

M6 flange bolt for lawn and garden equipment engines. Replaces broken, stripped, or missing bolts. Secures engine components and covers.

M6 x 1 flange bolt for outdoor power equipment. Secures engine covers, handles, and components. Replace if stripped, rusted, or missing threads.