Parts for Ge PDWT200V50BB: 01 - Escutcheon & Door Assembly Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Fix a dishwasher that stops mid-cycle or shuts down after 20-30 minutes. This thermostat kit regulates water temperature for proper heating and drying.

This hex washer-head screw is used in dishwashers to secure panels, brackets, and other hardware. Replacing a missing or corroded fastener restores a tight, stable installation and helps stop looseness or vibration during cycles.

• Fastens dishwasher panels, brackets, trim, or mounts to the cabinet/frame
• Replaces lost or stripped hardware after service or installation
• Helps address loose or rattling panels and minor misalignment
• Stainless steel construction per OEM spec for moisture-prone environments

• Disconnect power and water supply before servicing the dishwasher
• Wear gloves; sheet metal edges can be sharp
• Start threads by hand to avoid cross-threading; tighten with an appropriate driver
• Do not overtighten, especially when threading into plastic

Fix a broken or cracked dishwasher door handle. Simple repair requires only a Phillips and star screwdriver. Takes about 30 minutes to replace.

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

Replacement mounting screw for dishwashers. Secures components and panels inside the unit. Order a new screw if yours is stripped, missing, or damaged.

Fix dishwashers with unresponsive controls or display issues. This wire harness connects the control panel to the main board. Moderate difficulty repair.

The Blower Motor Assembly is an OEM part for GE dishwashers. This part is responsible for driving the dishwasher's venting system, which plays a key role in the drying process of your dishes.

Over time, the Blower Motor Assembly may need replacement due to wear and tear, damage, or failure. A malfunctioning blower motor can lead to ineffective drying of dishes, increased cycle times, or the dishwasher failing to complete its drying cycle properly.

Symptoms of a bad Blower Motor Assembly include:

• Dishes remaining damp or wet even after the drying cycle is complete.
• Unusual noises coming from the dishwasher, indicating that the blower motor is struggling to operate.
• The dishwasher stopping or pausing during the drying cycle.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This inlet transition is a molded connector that fits between the appliance cabinet and the inlet opening to guide incoming air and help maintain a sealed airflow path. It restores proper fit and reduces air leakage where the inlet meets the cabinet. What it does:

• Provides a finished, secure connection at the appliance inlet to direct airflow into the unit
• Helps reduce air leaks that can reduce drying/heating performance or cause airflow imbalance
• Replaces worn, cracked or broken inlet trim that can rattle or vibrate during operation
• Restores correct clearance and sealing where the inlet joins the cabinet

• One inlet transition piece

• Basic hand tools typically required; access the inlet area by removing the back panel or service panel as applicable
• Handle carefully to avoid bending or damaging adjacent trim and mounting tabs
• Disconnect power (and gas if applicable) before beginning service; follow all safety precautions in the appliance manual
• If mounting hardware is missing or damaged, replace with OEM-specified fasteners for secure fit

Replaces the lower access panel on your dishwasher to restore a finished look and protect internal components. Needed when cracked, damaged, or missing.

Hex washer head screw secures panels, brackets, and shields inside your appliance. Replace missing, stripped, or corroded fasteners for proper fit.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Dishwasher won't start or run? A faulty door latch prevents cycles from beginning. This assembly secures the door and engages the safety switch. DIY fix.

Detergent door won't stay closed or latch broken? This dishwasher dispenser releases soap and rinse aid during cycles. DIY repair in 20-30 minutes.

Replacement cap that seals the rinse aid dispenser on your dishwasher door. Replace if cracked, broken, warped from heat, or missing to prevent leaks.

Secures the detergent dispenser to the dishwasher inner door panel. Replace if cracked, broken, or rusted to restore proper alignment and mounting.

The GE screw is an OEM replacement part responsible for securing various components and parts of the dishwasher together. The screw is designed to provide a tight and secure connection for different panels, brackets, or other elements within the dishwasher. It plays a crucial role in maintaining the structural integrity of the appliance by preventing loose parts.

Common causes of a bad screw can include regular wear and tear from frequent use, exposure to moisture leading to corrosion, or damage from over-tightening. A compromised screw can result in loose or unstable components, which can affect the dishwasher's performance and safety.

Symptoms of a bad screw include:

• Loose or wobbly components within the dishwasher
• Difficulty in securing parts properly
• Visible rust or corrosion on the screw
• The screw head being stripped or damaged

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replaces a cracked, broken, or missing dishwasher vent cover that mounts on the inner door panel. Shields the exhaust opening and directs airflow.

Replacement mounting screw for dishwasher door panels, control assemblies, and internal components. Needed when original screws are stripped, rusted, or missing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

Fix a dishwasher with no lights or non-functioning control panel. This control module assembly restores power to the tactile board and keypad functions.

Grinding noise during drying cycle? This vent door actuator opens and closes the dishwasher vent for proper airflow. Easy DIY fix, one screw install.

Includes 12 screws.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.