Parts for Electrolux E23BC68JPSFA: Fresh Food Doors Parts

The Air Filter is an OEM part for Frigidaire refrigerators designed to enhance the air quality inside the refrigerator, ensuring that food stays fresh and odor-free.

The Air Filter helps to remove unwanted odors and impurities from the refrigerator's circulating air. It absorbs and neutralizes common food odors, keeping your fridge smelling clean and pleasant. The activated carbon filter is 7 times more effective than baking soda at removing odors. 

For best results, change filter every 6 months. 
Color: Black. 
Measures about 7 inches wide by 5 inches deep. 

Symptoms of a bad air filter include:

• Lingering food odors inside the refrigerator
• Increased presence of stale or unpleasant smells
• Decreased effectiveness in eliminating odors

Replace your Air Filter with this genuine part to ensure a clean and fresh-smelling refrigerator. This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Fresh Food Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the refrigerator door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper refrigerator conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the refrigerator
• Difficulty keeping the refrigerator door fully closed
• Warm air entering the refrigerator, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

NOTE: GASKET NOW GRAY, NOT WHITE

Flip-up cover for the cheese and butter compartment on your refrigerator door. Replace if cracked, broken, or missing to keep dairy items contained.

Nameplate label for refrigerators. Attaches to the exterior or interior panel. Replace if the original is faded, peeling, damaged, or missing.

Door stop component for bottom-mount refrigerators. Prevents door from swinging too far. Replace if cracked, broken, or missing for proper operation.

Mounts inside refrigerator to limit door travel and maintain proper alignment. Replace if cracked, broken, or missing to restore correct door positioning.

Three-piece refrigerator door handle set for bottom-mount models. Replace cracked, broken, or worn handles to restore appearance and functionality.

Mounting screw for refrigerator components and panels. Replace if stripped, missing, or damaged during repairs to secure parts properly.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Replaces a worn or missing door stop cam riser that holds your refrigerator door at the correct height for proper closing. Restores smooth operation.

Replaces worn or broken door stop bushing in bottom-mount refrigerators. Provides smooth bearing surface for door hinges. Order now if damaged or missing.

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

Clear refrigerator storage drawer bin door. Replaces cracked, broken, or missing door on compatible drawer frames. Restores sealed storage compartment.

Flip-up cover for the cheese and butter compartment on your refrigerator door. Replace if cracked, broken, or missing to keep dairy items contained.

Replace a stripped, missing, or damaged set screw that secures refrigerator or freezer door handles. Requires 3/32" allen wrench for installation.

Secures door handle to refrigerator door. Replace if missing, stripped, rusted, or corroded from regular use. Essential hardware for handle installation.

Hinge pin that secures the mullion flapper between split refrigerator doors. Replace if cracked, broken, or missing to restore proper door alignment.

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

Flip-up divider that seals the gap between refrigerator doors, preventing air leaks and moisture buildup. Replace if damaged, cracked, or no longer sealing properly. Verify fit with your model number.

Replacement door liner guide for bottom-mount refrigerators. Aligns and supports the door liner panel. Replace if cracked, broken, or worn out.

Replaces broken or cracked center hinge for refrigerator flapper door. Secures the center seal baffle between split doors. Includes mounting hardware.

The Air Filter is an OEM part for Frigidaire refrigerators designed to enhance the air quality inside the refrigerator, ensuring that food stays fresh and odor-free.

The Air Filter helps to remove unwanted odors and impurities from the refrigerator's circulating air. It absorbs and neutralizes common food odors, keeping your fridge smelling clean and pleasant. The activated carbon filter is 7 times more effective than baking soda at removing odors. 

For best results, change filter every 6 months. 
Color: Black. 
Measures about 7 inches wide by 5 inches deep. 

Symptoms of a bad air filter include:

• Lingering food odors inside the refrigerator
• Increased presence of stale or unpleasant smells
• Decreased effectiveness in eliminating odors

Replace your Air Filter with this genuine part to ensure a clean and fresh-smelling refrigerator. This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Replacement trim piece for refrigerator air filter door. Secures and finishes the filter cover for a clean look. Replaces cracked, chipped, or missing trim.

Covers and protects your refrigerator's air filter. Replace if cracked, broken, or won't secure the filter properly. Confirm fit with your model number.

Replaces cracked, broken, or dented refrigerator cabinet housing. Provides structural support and protects internal components. Restores proper fit.

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

Rubber door bumper cushions refrigerator door closure to reduce noise and protect cabinet finish. Replace if cracked, missing, or worn from repeated use.

Wire harness for refrigerators. Connects electrical components inside your unit. Replace if wires are frayed, damaged, or connectors are broken.

Fix a refrigerator door that won't close or stay shut with this door latch. Simple repair that restores proper door seal and cooling efficiency.

Replace your refrigerator's dairy door knob if it's cracked, broken, or missing. This knob installs on the dairy compartment door for easy opening and closing.

Genuine mounting screw secures panels, brackets, and components inside your refrigerator. Replace missing, stripped, or damaged screws to stop rattling.

Mounting screw for refrigerator components and panels. Replaces lost, stripped, or damaged screws. Essential hardware for secure assembly.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head