Parts for Ge PFCS1NFYCSS: 04 - Fresh Food Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Mounting screw for dryers, refrigerators, and side-by-side units. Replaces lost, stripped, or damaged screws during appliance repairs or maintenance.

Air tower duct assembly that channels cold air from freezer to fresh food compartment. Replace if cracked, broken, or causing uneven cooling airflow.

Refrigerator air tower duct that channels cold air from the evaporator to the fresh food compartment. Replace if cracked, broken, or missing parts.

Fridge running warm or uneven temps? This air tower assembly channels cold air through the refrigerator. Restores proper airflow and consistent cooling.

Seals the fresh food compartment inlet to maintain temperature and prevent air leaks. Replace if torn, cracked, or causing cooling issues. Verify fit with your refrigerator model number before ordering.

Replace your refrigerator tower fresh food gasket to restore proper sealing and prevent air leaks. Essential when doors don't seal tightly or foam shows wear. Verify compatibility with your model number before ordering.

Seals the fresh food compartment tower to prevent air leaks and maintain temperature. Replace if worn, cracked, or causing frost buildup. Verify fit with your refrigerator model number before ordering.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.

Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.

Symptoms of a bad Temperature Sensor Seal include:

• Inaccurate temperature readings.
• Condensation or frost near the sensor location.
• Frequent cycling or unusual patterns in the refrigerator's cooling process.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Light Bulb (40W) is an OEM component for GE refrigerators. As an essential task lamp, it illuminates the interior of the refrigerator and freezer compartments. 

All light bulbs will eventually burn out with consistent use over many years. Vibration during compressor cycles can also potentially disrupt bulb filaments faster. 

Symptoms of a burnt out refrigerator light bulb include:

• Dim or no light illuminating inside refrigerator shelves  
• Shadows and dark spots making it difficult to find items
• Higher utility costs from leaving the door open to see inside

This bulb is also compatible with refrigerators from brands like Hotpoint, RCA, and some Kenmore models. 

This light shield is the clear cover over the fresh food compartment light. It diffuses brightness and protects the bulb or LED from bumps, restoring even illumination and a finished look inside your refrigerator.

• Covers and protects the fresh food compartment light assembly
• Diffuses light to reduce glare and hot spots
• Replaces a cracked, yellowed, loose, or missing light cover/lens
• Helps the lens stay secured when original tabs are broken

What's included: One light shield for the fresh food compartment. Install notes:

• Unplug the refrigerator or switch off power before service
• Allow the lamp to cool; remove shelves for access if needed
• Release retaining tabs or hardware, noting the shield's orientation
• Seat the new shield fully; avoid forcing tabs or overtightening hardware

The Light Socket is an OEM part for GE refrigerators. It is responsible for holding the refrigerator's light bulb and ensuring it receives power to illuminate the interior when the door is opened.

You should replace the light socket if it becomes faulty. Causes of a bad light socket can include wear and tear from regular use, electrical issues such as short circuits or power surges, and corrosion from moisture exposure.

Symptoms of a bad light socket include:

• The refrigerator light not turning on when the door is opened
• Flickering or intermittent light operation
• Visible damage or corrosion on the socket
• The light bulb not fitting securely or falling out

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This vertical vent duct is a direct-replacement exhaust channel that routes hot, moist air from the appliance to the home vent, helping maintain proper airflow and reduce moisture or heat buildup around the unit. What it does

• Channels exhaust air from the appliance to the household vent line.
• Helps prevent exhaust air from leaking into the room and reduces backflow.
• Common symptoms it can address: long drying cycles, excess humidity or heat near the appliance, and visible exhaust escaping into the room.
• Fits into the appliance's existing vent connection to restore correct airflow.

• Turn off and disconnect power (and gas, if applicable) before servicing.
• Verify the existing vent path is clear and the duct orientation matches appliance connections.
• Use basic hand tools; avoid crushing or kinking the duct during installation.

Vertical vent duct channels air inside your refrigerator cabinet for consistent temperature control. Replace if cracked, warped, or missing to restore airflow.

Replace your refrigerator light cover lens if cracked, yellowed, or missing. Protects the interior bulb and ensures proper illumination. Verify fit with your model.

Fridge running warm or uneven temps? This air tower assembly channels cold air through the refrigerator. Restores proper airflow and consistent cooling.

Secures and seals your refrigerator's water filter cartridge in place. Replace if cracked, loose, or leaking to restore proper fit and prevent debris entry.

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Houses the water filter and connects to the water supply line. Replace if water leaks, sprays during filter changes, or dispenser flow decreases. Verify model fit.

Bypass cap allows refrigerator water and ice dispensers to work without a filter installed. Replace if cracked or leaking. Confirm fit with your model.

Spacer component for refrigerator water filter housing. Ensures proper spacing and alignment. Replace if cracked, worn, or missing to restore fit.

Fix blank displays, inaccurate temperature readings, or unresponsive controls. This control board regulates cooling cycles and monitors sensors. Moderate DIY.

This grille sensor is the temperature-sensing probe that monitors heat in the appliance grille area to help controls regulate cooking temperature and safety features. It provides accurate feedback so the oven or grill can maintain set temperatures. What it does:

• Senses temperature in the grille/grill area and sends readings to the control board
• Helps the appliance maintain consistent cooking or broiling temperatures
• Can cause temperature-related errors or inconsistent heating when failed
• Common symptom: oven or broil function runs too hot, too cool, or shows error codes related to temperature sensing

• One grille sensor

• Disconnect power to the appliance before any service to avoid shock or injury
• Handle the sensor carefully; avoid bending or contaminating the sensing tip
• Route and secure the sensor wiring as OEM designed to prevent heat or pinch damage