Parts for Ge GTE16DTHCRBB: Fresh Food Section Parts

Refrigerator not cooling or ice building up on evaporator coils? The defrost timer controls the defrost cycle. DIY-friendly, installs in 5 minutes.

Leveling leg threads into the refrigerator base to support and stabilize the cabinet. Replace if cracked, broken, or worn to keep your unit level.

Secures and guides your refrigerator door for smooth operation. Replace when door sags, misaligns, or fails to seal properly. Confirm fit with your model.

Replace your refrigerator's center door hinge to restore smooth door movement and maintain a proper seal. Supports door weight at the pivot point. Confirm fit with your model number before ordering.

Pivot shaft for refrigerator doors at the middle hinge. Replace if worn or bent to restore proper door alignment and smooth operation. Verify fit.

Black corner cap cover for top-mount refrigerators. Replaces cracked, broken, or missing corner trim pieces. Installs on exterior cabinet edges.

Small washer that fits on refrigerator door hinges to distribute weight and reduce friction. Replace if worn, cracked, or missing to restore proper alignment.

Supports the refrigerator door at the lower pivot point for smooth opening and proper sealing. Replace if the door sags or won't close tightly. Confirm fit by model number.

Bottom hinge pin secures the refrigerator door at the base, allowing smooth opening and closing. Replace if worn, damaged, missing, or door sags.

Left front wheel assembly for refrigerators. Installs at the front base to allow smooth rolling. Replace if wheel is cracked, broken, or worn.

Right front wheel assembly for refrigerators. Installs on the bottom right corner for smooth rolling. Replace if cracked, broken, or missing.

Control knob fits onto your refrigerator's control shaft to adjust temperature and settings. Replace a cracked, stripped, or missing knob for smooth operation.

Fridge not cooling consistently? This temperature control thermostat cycles the cooling system to maintain proper temps in both compartments. Restores reliable cooling.

Foam gasket seals the water supply nozzle connection to prevent leaks and reduce vibration. Replace if worn or leaking. Confirm fit with your model number.

Vinyl sleeve that fits over rods, tubes, or wires in your refrigerator. Replace if cracked, torn, or missing to protect contact points and reduce wear.

Molded chassis that supports and positions the refrigerator control panel components. Replace if cracked, broken, or damaged to restore secure mounting.

The Light Socket is an OEM part for GE refrigerators. It is responsible for holding the refrigerator's light bulb and ensuring it receives power to illuminate the interior when the door is opened.

You should replace the light socket if it becomes faulty. Causes of a bad light socket can include wear and tear from regular use, electrical issues such as short circuits or power surges, and corrosion from moisture exposure.

Symptoms of a bad light socket include:

• The refrigerator light not turning on when the door is opened
• Flickering or intermittent light operation
• Visible damage or corrosion on the socket
• The light bulb not fitting securely or falling out

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix interior lights that won't turn on, stay on constantly, or delay when opening the door. This switch replacement takes 10-15 minutes with basic tools.

This silicon controlled rectifier (SCR) is an electrical switching device used on appliances to regulate power to heating elements and motors. It restores reliable power flow for consistent operation when the original SCR fails. What it does:

• Controls and switches current to heating elements or motors for temperature and power regulation
• Prevents uncontrolled power delivery that can cause erratic heating or cycling
• Common symptom: appliance won't heat or heats inconsistently
• Common symptom: appliance displays erratic temperature control or intermittent operation

• One silicon controlled rectifier (SCR) unit

• Disconnect all power at the breaker before accessing or replacing the SCR
• Handle the part carefully; avoid contact with conductive terminals and observe ESD precautions
• Use the original mounting hardware and torque to OEM specifications where applicable

This genuine fastener secures appliance components such as panels and brackets. Replacing a missing or stripped screw restores proper fit and helps reduce vibration or rattling. Features 12-24 threads and an approximate 0.785-inch length. What it does:

• Fastens panels, brackets, covers, and other hardware points in the appliance
• Helps maintain proper alignment and a tight fit of components
• Replaces damaged, stripped, or missing hardware
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power before servicing; shut off water supply if working near water components
• Start the screw by hand to avoid cross-threading; replace one-for-one in the original location
• Use the correct driver bit for the head style; tighten snugly without overtightening into plastic or thin metal