Frigidaire Washer Parts

Fix a washer that won't drain or leaks during the drain cycle. This pump and hose assembly restores water removal. Direct-fit installation for most models.

Fix a washer that won't spin, shows error codes, or has unresponsive controls. This main control board coordinates all cycles and functions. DIY-friendly.

Replaces cracked, warped, or broken inner door panel on front-load washers. Restores door structure and provides mounting surfaces for bins and seals.

Spacer that positions and cushions the agitator screw in top-load washers. Replace if worn, cracked, or missing to maintain proper agitator alignment.

This access panel service cover replaces a damaged or missing cover to protect internal components and give technicians safe access for diagnostics and repairs. It restores a finished appearance while preventing dust and debris from entering service areas. What it does:

• Covers and protects internal components, wiring and controls from dust and damage.
• Provides a removable service access point for diagnostics and repairs.
• Common symptoms: cracked, bent, loose or missing panel; exposed components; rattling or drafts near the service area.
• Replacement helps restore safety, reduce drafts and eliminate noise caused by a loose or damaged panel.

• Disconnect power (and water if applicable) before removing or installing the panel.
• Wear gloves to protect hands from sharp sheet-metal edges.
• Reuse existing screws or mounting clips when possible; basic hand tools typically required.

Replacement water inlet valve that controls water flow to the refrigerator's ice maker and dispenser, restoring proper water delivery and helping stop leaks or no-water conditions when the factory valve fails. What it does:

• Opens and closes the water supply to the ice maker and dispenser when signaled by the refrigerator's control board.
• Commonly linked to symptoms such as no water from the dispenser, slow fill, or ice maker not filling.
• Can fail by leaking, sticking closed, or not responding to electrical signals.
• Works with the refrigerator's tubing and fittings to route incoming household water to internal components.

• Disconnect power and shut off the refrigerator water supply before beginning work.
• Relieve water pressure and have towels handy to catch residual water when removing tubing.
• Verify electrical connector and inlet/outlet fittings match the appliance; replace any damaged tubing or seals.

Right hand side. For screws use WPW10119828.

Replacement mounting screw for washers and laundry centers. Secures components like pulleys, brackets, and panels. Replace if missing, stripped, or damaged.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Rotary control knob that fits onto the control shaft to select settings. Replace if your original knob is cracked, broken, worn, or missing.

Fix a washer that won't advance through cycles or gets stuck washing or spinning. This control timer regulates cycle progression. Moderate DIY repair.

This evaporator fan motor circulates cold air through the freezer and refrigerator compartments to help maintain even cooling and proper defrost airflow. Replacing a worn motor restores airflow and helps the fridge reach set temperatures more reliably. What it does:

• Spins the evaporator blower to move cold air from the evaporator through the cabinet.
• Restores airflow when the motor has failed, slowed, or runs intermittently.
• Helps reduce uneven cooling, warm spots, and extended run times caused by poor air circulation.
• May stop making excessive noise or vibrating when a worn motor is replaced.

• Disconnect power to the appliance before beginning any service.
• Access typically requires removing the freezer evaporator cover or rear interior panel—keep screws and small parts organized.
• Handle evaporator fins and blower wheel carefully to avoid damage; check clearance and wheel alignment during reassembly.

Return spring for washer door lock mechanism. Restores tension so the latch returns to proper position. Replace if worn, missing, or causing loose latch.

This replacement vent manages internal airflow within your appliance, routing air through the intended path. Restoring a damaged or missing vent helps maintain performance and reduces heat and moisture buildup inside the cabinet. What it does:

• Directs and regulates airflow through the appliance's air path
• Helps maintain proper pressure balance and efficient moisture removal
• Reduces the chance of lint or debris bypassing the intended ducting
• A cracked, warped, missing, or clogged vent can contribute to weak airflow, longer cycles, excess heat, or unusual noises

• 1 vent

• Disconnect power before servicing; allow hot components to cool
• Access the vent by removing the appropriate panel; note screw and clip locations
• Transfer any mounting hardware or seals from the old vent and ensure proper orientation
• Clear lint/debris from adjoining ducts before reassembly; test run to ensure smooth airflow and no rattling

This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What it does

• Creates the viewing window in the door and mates to the door gasket/boot
• Helps maintain a proper seal to contain wash action
• Restores safe operation when the original glass is damaged
• Common symptoms: visible cracks or shattering, water leaking from the door area, door not closing flush, rattling glass

• 1 door glass pane

• Disconnect power and turn off water supply before service
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door, set it on a padded surface, and transfer trim/gasket as designed
• Tighten fasteners evenly and check gasket alignment to prevent leaks

Almond. Size: 13 oz. can. Acrylic appliance paint.