Frigidaire Washer Parts

Washer air chamber connects the water level pressure switch to the tub. Replace if cracked, kinked, or disconnected causing water level issues.

This replacement cup funnels water to the ice maker fill tube and helps ensure proper water delivery for consistent ice production. It restores the fill path and prevents water from pooling where it can cause poor ice formation or leaks. What it does

• Directs water into the ice maker fill tube so molds receive the correct amount
• Helps prevent water from spilling into the ice bin or cabinet area
• Addresses symptoms like slow/weak ice production, water pooling under the ice maker, or visible leaks during a fill cycle
• Works with the ice maker assembly to maintain consistent ice size and formation

• One replacement ice-maker fill cup

• Disconnect power and shut off the water supply before servicing the ice maker
• Remove the ice maker or access panel per your model's service instructions to reach and replace the cup
• Handle plastic parts gently to avoid cracking; ensure a snug fit to prevent leaks
• If symptoms persist after replacement, check the fill valve and ice maker assembly for proper operation

Fix a washer that won't advance cycles or start filling water with a new timer. Controls cycle timing and electrical components. 10-15 minute DIY repair.

This suspension spring supports the washer tub and helps stabilize the drum during spin cycles to reduce vibration and noise. Replaces a worn or broken tub spring to restore smoother operation. What it does

• Holds and stabilizes the inner tub assembly to limit excessive movement during spins
• Helps reduce vibration and rattling that can occur from a loose or broken spring
• Prevents tub misalignment that can cause rubbing or noise
• Works with the washer's suspension system to maintain proper spin balance

• One suspension (tub) spring as shown

• Disconnect power and water supply before starting any repairs
• Springs are under tension; use caution and proper tools to remove/install
• Inspect other suspension components (shocks/rods, mounts) and replace if worn

This leveling foot assembly restores a stable, level base so your machine runs smoothly and stays in place. It replaces a worn or stripped foot with a new bolt, pad, and nut to secure the adjustment.

• Levels and supports the appliance by adjusting the foot height
• Helps reduce vibration, rocking, and walking during operation
• Replaces stripped, bent, or rusted foot bolts and worn or missing pads
• Holds the set height with the included nut to maintain alignment

• Disconnect power; for washers, turn off water supply before servicing
• Carefully tip and support the appliance to access the feet
• Thread the new foot into the base, seat the pad, and tighten the nut
• Level front-to-back and side-to-side; ensure all feet are firmly on the floor

Mounting bracket secures components inside your laundry center. Replace if bent, broken, or missing to eliminate rattling and restore stability.

Fix washer overfilling or incorrect water levels with a new pressure switch. Solves fill problems across load sizes. Most installs in 5-10 minutes.

Trunnion assembly for washing machines. Supports and allows outer tub rotation during wash and spin cycles. Replace if cracked, worn, or damaged.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

This replacement door gasket seals the refrigerator/freezer door to help maintain consistent temperatures and reduce frost buildup. It restores the cabinet seal so the appliance can cool efficiently and run less often. What it does:

• Provides an airtight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and freezer run time caused by leaks
• Can stop common symptoms like warm spots inside the compartment, excessive frost, or frequent compressor cycling
• Fits into the door channel and compresses to form a continuous seal when the door is closed

• Disconnect power to the appliance before starting any repairs
• Remove the old gasket and thoroughly clean the door channel before installing the new gasket
• Press the gasket evenly into the channel, working around the door to ensure a continuous, wrinkle-free seal
• Avoid using sharp tools that could damage the new gasket; allow the gasket to fully seat before checking for leaks

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

Mounting bracket secures internal components and panels in your washer. Replace if bracket is cracked, broken, or missing to restore proper alignment and support.

Fix a washer that loses power, won't spin properly, or has an unresponsive control panel. This electronic control board restores normal operation.

This mechanical defrost timer advances the refrigerator's defrost cycle to help prevent excessive frost and ice buildup on the evaporator. Replaces a failed timer to restore automatic defrosting and more consistent cooling. What it does:

• Cycles the refrigerator between cooling and defrost modes on a timed schedule
• Initiates heater and compressor changes to melt frost accumulation
• Common symptom: heavy frost or ice on the evaporator or inside freezer compartment
• Common symptom: unit runs continuously or cooling performance is inconsistent

• Disconnect power to the appliance before any repair to avoid shock
• Locate timer (behind kick plate, control panel, or at rear) and note wire positions or take a photo before removing
• Swap the old timer for the replacement and reconnect wires to matching terminals

Replacement pin for washer components. Secures and connects internal parts. Needed when original pin is broken, missing, or worn from use.