Parts for Dacor ER30GISCHNG: Grates Parts

This low-profile backguard assembly replaces the rear control-panel backshield on compatible Samsung ranges. It restores finished appearance, protects wiring and controls from heat and spills, and supports the control console for safe operation. What it does:

• Covers and protects rear control components from heat, grease and spills
• Provides structural support for the control console and control wiring
• Replaces cracked, dented or missing backguard trim that exposes internal parts
• Helps prevent debris and liquids from entering the appliance rear area

• One low-profile backguard assembly

• Disconnect power to the range before starting any repair
• Remove backing panels or control console per the service manual; some panels may be sharp
• Keep hardware removed during disassembly; verify fit before final fastening

Factory wafer-head Phillips screw (#8 x 3/8 in) secures panels, brackets, and covers. Replace missing, stripped, or damaged screws for proper alignment.

Fix uneven flames or weak heat on your gas cooktop with this replacement burner cap. Restores proper flame shape when the original is cracked or chipped.

This surface burner ring replaces a damaged or worn gas cooktop burner ring to restore even heat distribution and reliable surface burner operation. It fits single-burner cooktops and helps improve ignition and flame stability. What it does

• Sits around the burner cap to direct and distribute flame for consistent cooking heat.
• Restores proper burner airflow when warped, cracked or corroded, helping improve ignition and steady flame.
• Helps eliminate uneven cooking and sputtering flames caused by damaged burner rings.
• Compatible with liquid propane (LP) 15K burner configurations where this ring is specified.

• One surface burner ring.

• Turn off gas supply and disconnect power to the appliance before starting any repair.
• Remove grate and burner cap, then lift out the old ring and seat the replacement ring in the cooktop recess.
• Check burner cap alignment and ignition after installation; inspect for gas leaks before use.

Fix uneven flames or poor ignition with this range burner cap. Restores proper flame shape and heat distribution on your gas cooktop. Simple DIY fix.

This inner burner service ring restores the sealed area around a gas cooktop's inner burner, helping stabilize the burner assembly and improve ignition reliability. Fits as the inner ring component used with the burner cap. What it does:

• Replaces a worn or damaged inner ring that supports the burner cap and burner head
• Helps maintain even gas flow and a stable flame pattern when the ring is intact
• Can reduce ignition issues caused by a warped or cracked inner ring
• Restores proper seating of burner components after service or repair

• One inner burner service ring

• Installation requires removing the burner cap and burner head; follow your appliance's service manual
• Ensure gas supply is off and surface is cool before servicing
• Handle porcelain- or enamel-coated parts carefully to avoid chipping

This outer surface burner ring replaces the damaged or worn ring on a gas cooktop, restoring proper gas flow and burner alignment for safer, more even heating. Fits specified Samsung surface burners. What it does:

• Replaces a cracked, warped or corroded outer burner ring to re-establish correct burner geometry
• Helps restore consistent flame pattern and even cooking across the burner
• Can resolve issues like uneven heating or gas flame wandering at the burner edge
• Works with the matching inner burner and cap to form the complete burner assembly

• One outer surface burner ring

• Turn off gas supply and disconnect power to the appliance before servicing
• Allow all components to cool completely; burner parts may have sharp edges—wear gloves
• Remove burner cap and inner components, seat the new outer ring fully before reassembly

Uneven flames or poor heat distribution? This outer burner cap protects the burner head and restores proper flame pattern for consistent cooking results.

If your burner flame is uneven or won't ignite properly, the burner cap may be damaged. This inner cap sits over the 18K burner head to shape flames.

M4 x 12mm stainless steel service screw secures panels and small components in your cooktop or range. Replace worn, stripped, or missing screws.