Ikea Gasket & Seal

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

My Whirlpool dishwasher was leaking out the bottom of the door. I replaced the gasket and the lower door seal. When I ran a test wash, it was still leaking. After reading more online, I found that it could be a cracked washer arm. The initial inspection of the washer arm looked normal but when I used my faucet to slowly pour water into the inlet of the arm, I noted that water was leaking through a seam and not just the holes where it should come out. I then tried running a wash without the... Read more

Thanks to Jason and his tech people at Appliance Parts Pro, I was able to remove and replace the seal and eliminate all leaks at the bottom of the door. I have a Kitchenaide (Whirlpool) dishwasher model KUDC10IXBL1. Here is how to replace the bottom door seal. 1) Shut off breaker to dishwasher on the electrical panel. 2) Open the dishwasher door completely, and while supporting the door, remove the hex head screws that hold the outside cover. 2) Close the door carefully and slip the outside... Read more

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

A quick google search lead me to the problem - the plastic door gasket had become loose and broken. Received the part very quickly and installed it that night after a little trial and error. What the videos don't tell you is that to properly 'seat' the gasket you need to angle it UP when you push it into the little gap. If you angle it up, it will catch and seat properly, if you just push it in normally, it won't catch on the right part and it'll just hang loose at the bottom of the door and... Read more

Thanks to the Appliance Pro video and next day delivery, the fix was easy. Removed the old seals by hand and placed the new seals around the door shelves and eased it into the grove in the door. Read more

Removed freezer door by removing 4 bolts holding slide tracks for freezer basket. Pulled out old gasket. Soaked new gasket in hot water to smooth out a crease that resulted from shipping. Installed new gasket, starting at corners. Used a blunt tool to push new gasket into slot at the corners. Set remaining gasket material with hands. Used putty knife to tuck edge of gasket under lip along door. Reinstalled door. Take care to line up door perpendicularly. There is some play when... Read more

Door gasket was easy to remove and reinstall. Original gasket was penetrated while cleaning food stuff from folds in the seal below the frig doors. (Gasket is very fragile so don't try to expand the folds while cleaning. I used my finger and a paper towel but in hindsight should have used a Q-Tip. Also, when installing the new gasket you have to be sure the seam folds over the edge of the door and doesn't get caught underneath. Read more

The tray was simple, pick up the old one, pop in the new one. The gasket for my refrigerator was almost as easy. When I received the part I opened it up and let it lay flat for about 3 days (probably overkill). The old gasket popped right out and the new one went in really easy. The entire job took me about 10 minutes to do, no tools required. I do recommend that you start with corners and work your way to the middle of each side. I found that would prevent any stretching. You also need to... Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

Did some online research and everything pointed to the fact that moisture was getting into the freezer and therefore the seal was not doing it's job. I ran my finger along the seal and sure enough I detected cold air coming out of one corner of the seal. I ordered the appropriate part from Appliance Parts Pros (APP) but decided to test my diagnosis by installing thin weather stripping in the affected area. I checked the freezer the next day and saw no accumulation of any more Rime ice so... Read more

I determined that the gasket was pinched, leaking at corner. Ordered new gasket from this site (easy find with part diagram). Removed old gasket, replaced with new. Read more

Ordered new seal pulled old one off and put new one in its place Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

I found the gasket on your website. I watched the installation video provided. I purchased the gasket and installed it. It was inexpensive and painless. I will order from you again. Thanks Roger Read more

Placed the robber seal Read more