Parts for Maytag JDB3600AWS3: 03 - Inner Door Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Fixes loose panels, rattling doors, or wobbly components caused by stripped or missing screws. Secures brackets, covers, and mounting hardware. Easy DIY.

This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.

• Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
• Helps maintain alignment and reduce vibration/rattling
• Direct replacement for stripped, corroded, or missing screws
• Common signs: loose panels or trim, shifting components, screw won't tighten

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace one-for-one in the original location per service information

The Air Inlet is an OEM part for Whirlpool dishwashers. It draws in ambient room air to assist in drying dishes after wash cycles have been completed. With openings around its base, the air inlet facilitates airflow through the dish rack to evaporate residual moisture left on rinsed dishes.

Causes of a bad air inlet can include cracks in the plastic preventing proper draw of air currents, or obstructions blocking air pathways.

Symptoms of a bad air inlet include:

• Dishes remaining wet and not fully dried after cycles
• Puddles or watermarks left behind on upper racks and dishes
• Slow air movement detected near the bottom air vents
• Musty odors or smells developing inside the dishwasher

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Also order air vent gasket

Seals the dishwasher air vent to prevent water leaks during operation. Replace if you notice dripping under the vent or wet insulation behind the panel.

Directs airflow in your dishwasher's vent system. Replace if cracked, discolored, or blocking proper ventilation. Confirm fit with your model number.

Detergent not dispensing or dispenser door won't open? This dishwasher dispenser assembly fixes release issues. Moderate DIY repair—45 minutes.

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Fix a dishwasher that won't start or has electrical issues with this wire harness. Connects control components to power supply. Moderate DIY repair.

The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.

If your detergent dispenser is loose or falling off, this bracket secures it to the door panel. Moderate DIY repair requiring door disassembly.

Fix a broken or missing dispenser lid that causes detergent spills or won't stay closed. This dishwasher dispenser cover restores proper function.

Color: gray. It measures about 1-1/2 inches in diameter.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.