Jenn-Air Washer Parts

• Spins slowly
• Burning smell
• Pumps but will not spin
• Noisy

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

• Burning smell
• Will not agitate
• Spins slowly
• Pumps but will not spin

I Purchased a new belt and replaced it. If I had not watched the video telling me how it is done the job would have been much more difficult. After watching the video I changed the belt in less than 2 minutes. I ordered the belt from Appliance Parts Pros and got it the next day. I am thankful that when I started my search I landed on your web site. Thanks for the quick service and the video. Read more

• Spins slowly
• Pumps but will not spin
• Will not agitate

My Maytag washer make a loud screech when the washer tub needed to be stopped by the brake. Last year, I had replaced the suspension springs, the snubber ring, the drive belt and the drain pump. Those repairs worked fine, but a few weeks later, the screeching noise started. So I figured it was the brake system. I thought it would be better to replace the brake rotor and stator together as a set since I was going to disassemble both and they were 18 years old anyway. I decided to replace the... Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Ordered the part, which was easy and smooth. Watched you tube video on how to repair. Took me 15 minutes. Easy as it could be. Read more

I ordered the tub seal and stem seal kits along with the much needed spanner wrench. After viewing the video online several times and taking notes along the way I was ready to tackle the repair. After taking everything apart, I cleaned all areas thoroughly then addressed the rusty areas and mineral deposits found in the tub. Soaking the tub in vinegar and baking soda overnight helped loosen the built up deposits enough so I could carefully scrape them off with a spatula. This was very time... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water
• Noisy

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

I ordered parts from appliance parts pro at 3:30 on Friday and they were delivered at bout noon on Saturday the next day. Took the machine apart removed the old pads. With the directions in the packages put it back together and the wife ran 5 loads of clothes through it. Works great. Was awesome to get the parts so quick Read more

I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Replaced the water valve. Easy repair. The repair video was spot-on. Tools needed: Slip joint pliers for removing and attaching the hoses and moving the hose clip. 5/16 nut driver. Phone to take a picture so I could get the wires put back right. Shut off the water and unplug from power. Remove the hoses. Using a 5/16 nut driver remove the single screw that holds the bracket, lift bracket slightly and pull from the washer. There is a little slack in wires and fill hose to work with. Take a... Read more

Touch up paint Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

Replaced It With New One Read more