Kenmore / Sears Cooktop Control Board

Oven won't heat to set temperature or display shows error codes? This electronic control board manages bake/broil circuits and clock functions. DIY repair.

This OEM replacement part is an oven control board. The oven control board is the primary computer circuit board that controls the main functions of the oven. These functions include turning the oven on as well as adjusting and maintaining the temperature of the oven. Luckily, replacing a control board is a simple process.To replace the board, first, make sure the oven is unplugged. Gain access to the back of the oven and remove the upper back panel. Once the panel is removed, locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Disconnect the wire harness and any individual wires that are attached to the old board. Re-secure the wires into their correct positions. Snap the new board back in place and reinstall the upper back panel.This genuine replacement control board is compatible with Frigidaire Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

Fix F11 error codes, non-working clock displays, or temperature control issues. This electronic control board restores oven function and display accuracy.

Oven won't heat, wrong element activates, or temperature swings wildly? This control board regulates heating circuits and display. Moderate DIY repair.

Fix an oven that won't heat or respond to controls with this electronic control board. Restores accurate temperature regulation and normal operation.

Fix F10 error codes, runaway oven temps, or ovens that won't heat with this range control board. Moderate DIY repair; disconnect power and remove back panel.

The Noise Filter is an OEM part for Whirlpool built-in wall ovens. It is installed inside the oven cavity near components that produce vibrations, such as the convection fan motor. 

Causes of a faulty noise filter include the degradation of noise-dampening materials over many heating and cooling cycles. Physical damage from accidental impact during cleaning could also compromise its sound-blocking ability.

Symptoms of a bad noise filter include: 

• Excessive buzzing or humming noises emitted from the oven cavity
• Louder than normal fan or component sounds carrying into the kitchen
• Vibrations felt externally on the oven chassis during operation

This OEM replacement fits several Whirlpool, KitchenAid, and Jenn-Air wall oven models.

Fix unresponsive buttons, error codes, or power surge damage with this range oven control board. Restores all cooking functions and timer operations.

Oven won't heat or display is blank? This electronic control board manages temperature, timers, and element power. Moderate DIY repair in 1-2 hours.

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

Range won't power on, clock or controls aren't working? The electronic control board manages all oven functions. DIYers report plug-and-play install.

Oven won't heat to temperature or overheats dangerously? The electronic control board manages all oven functions. Moderate DIY repair, about 1 hour.

Microwave won't turn on, made popping noise, or smells like burned electrical? The noise filter often fails when solder joints arc or short out.

Range won't turn on or display shows incomplete numbers? This electronic control board manages cycles and user inputs. Moderate DIY repair, 1-2 hours.

This ignition generator and wiring harness assembly routes power and provides the spark/ignition signal needed for gas appliance burners to light. It replaces a worn or damaged ignition assembly to restore reliable lighting. What it does:

• Sends ignition voltage to the burner igniters and electrodes so burners light reliably
• Routes and secures wiring between the control module and ignition components
• Common failure symptoms: burners won't light, continuous clicking, or intermittent ignition
• Works as the electrical interface between the control and the igniters for safe startup

• One generator and wiring harness assembly

• Disconnect electrical power and turn off the gas supply before starting work
• Follow the appliance OEM diagram for correct routing and connector locations
• Inspect connectors and electrodes for damage and replace if corroded or worn

This generator is the OEM replacement rotary cam assembly that times and drives mechanical sequences so your appliance operates correctly. It restores proper cycle sequencing to help eliminate failures caused by a worn or damaged cam. What it does:

• Rotates and indexes internal cams/gears to control mechanical switching and timing
• Ensures correct sequencing of cycles and component engagement
• Commonly replaces noisy, stuck, or non-indexing cam assemblies
• Helps resolve symptoms like intermittent operation, failed cycle changes, or mechanical binding

• One generator (rotary cam assembly) as shown

• Disconnect power before servicing to avoid shock or injury
• Access may require panel removal and basic hand tools
• Verify alignment and timing marks during installation for proper operation