Parts for Electrolux SFLG4033RW1: 05 - Lower Cabinet / Top Parts

Mounting screw for laundry center panels and components. Replace missing, stripped, or damaged screws to secure parts properly during assembly or repair.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

Top-loading washer lid for laundry center units. Replace if cracked, bent, or no longer closes securely. Installs with hinge screws at the rear.

Washer won't start or door won't close properly? This door striker secures your laundry center lid. Simple 2-screw replacement takes 10 minutes.

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

Replacement pin for washer components. Secures and connects internal parts. Needed when original pin is broken, missing, or worn from use.

Replacement cover panel for laundry center units. Installs on exterior cabinet to restore appearance when original is cracked, damaged, or missing.

Mounting bracket for washer dryer combo units. Secures components in place during operation. Replace if bent, cracked, or broken to restore stability.

Washer stuck in rinse cycle or won't spin? This electronic control board manages cycle logic and motor speed. Moderately difficult repair—requires panel removal.

Fix unresponsive controls, cycles that won't start, or blank displays. This electronic control board restores command functions and timer operations.

Washer not filling or filling slowly? This water inlet valve controls water flow into your washer. Moderate difficulty repair requires partial disassembly.

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

Water fill hose assembly connects your laundry center's water supply to the wash tub. Replace if cracked, leaking, split, or damaged to stop water leaks.

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

Replace your laundry center control panel when buttons don't respond or the console is cracked. Houses buttons, switches, and display for reliable operation.

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.

Small alignment pin that positions and secures panels or components during assembly. Replace when worn, missing, or damaged to restore proper fit.

This is a replacement 12-24 UNC machine screw used to secure appliance panels and internal components so fittings stay tight and stable during use. It restores proper fastening where the original screw is damaged or missing. What it does:

• Fastens and secures panels, brackets, and component assemblies
• Helps stop rattling, loose parts, or gaps caused by a missing or stripped screw
• Provides correct thread engagement for 12-24 UNC threaded holes
• Replaces worn, rusted, or damaged screws to restore original fit

• Disconnect power and water to the appliance before servicing
• Use the correct driver and size to avoid stripping the head
• Thread in by hand first, then tighten snugly—do not overtighten
• Replace only with the exact part number to ensure proper fit and function

The Lock is an OEM part for Frigidaire washers, designed to securely close the door. The mechanism engages at the start and releases at the cycle's end or pauses for drum access. Over time, it may wear out or malfunction, jeopardizing appliance safety and function.

Causes of a bad lock can include mechanical wear and tear from regular use, electrical faults within the lock mechanism, damage from forceful closing or opening of the washer door, and corrosion or buildup affecting the lock's components.

Symptoms of a bad Lock include:

• The washer door won't lock or unlock
• The washing machine fails to start a cycle due to the door not being securely locked
• An error code appears on the washer's display indicating a door lock issue
• Unusual noises from the door area when attempting to start a cycle

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Control panel for laundry center units. Replaces damaged, cracked, or broken front panel housing controls. Installs on exterior front of unit.

This is a replacement dispenser assembly for your refrigerator's door dispenser. It restores the external dispenser trim/assembly so you can use the ice and water dispensing area reliably and keep the door looking finished. What it does:

• Replaces a cracked, broken or damaged dispenser housing or trim piece
• Restores proper alignment and user interface for dispensing water or ice
• Helps stop drafts or moisture intrusion around the dispenser opening
• Can resolve cosmetic damage or functional issues where the dispenser lever/area is compromised

• Disconnect power and shut off the water supply before beginning work
• Remove the inner door panel as required to access and remove the old dispenser; keep fasteners for reuse unless damaged
• Handle the dispenser and door trim carefully to avoid scratching or cracking during installation
• After installation, restore power and water supply and check for proper operation and any leaks

Suspension spring that supports and stabilizes the wash tub during operation. Replace if broken, cracked, or worn to restore proper tub support.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Structural base for laundry centers and washer dryer combos. Replace if cracked, broken, or damaged. Provides stability and support for stacked units.

Control panel bezel surrounds and protects your laundry center's controls. Replace when cracked, discolored, or damaged to restore appearance. Confirm fit.