Parts for Frigidaire FFFW5100PW0: Motor / Tub Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replacement bolt fastener for securing washer panels, brackets, and assemblies. Needed when original bolt is missing, loose, or stripped causing rattling.

The Counterweight is an OEM part for Frigidaire washing machines. It is located at the front of the tub, helping to offset the weight of heavily loaded clothes and maintaining the best drum balance during centrifugal spin cycles. The counterweight is cast and matched to each washer model to distribute weight as efficiently as possible.

Causes of a bad counterweight can include cracks or fractures from extensive machine vibrations over time, or damage incurred during removal/installation.

Symptoms of a bad or missing counterweight include:

• Excessive tub or machine vibration
• Noisy or unbalanced spin cycles
• Clothes failing to extract fully due to off-balance load
• Potential tub or drum damage from stresses of imbalance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Secures the inner bellow seal to the tub in front-load washers. Replace if rusted, broken, or causing seal leakage. Tight installation requires patience.

Flexible gasket sealing washer door to drum, preventing leaks during cycles. Replace when torn, leaking, or showing mold buildup. Confirm fit.

Replacement mounting nut for washers and laundry appliances. Secures internal components and panels. Order if original nut is stripped, missing, or broken.

This suspension spring supports the washer tub and helps stabilize the drum during spin cycles to reduce vibration and noise. Replaces a worn or broken tub spring to restore smoother operation. What it does

• Holds and stabilizes the inner tub assembly to limit excessive movement during spins
• Helps reduce vibration and rattling that can occur from a loose or broken spring
• Prevents tub misalignment that can cause rubbing or noise
• Works with the washer's suspension system to maintain proper spin balance

• One suspension (tub) spring as shown

• Disconnect power and water supply before starting any repairs
• Springs are under tension; use caution and proper tools to remove/install
• Inspect other suspension components (shocks/rods, mounts) and replace if worn

Support plate for washer components. Mounts internally to secure parts in place. Replace if cracked, bent, or broken to restore proper structural support.

Outer cabinet shell that houses and protects washer components. Replace if your shell is cracked, dented, rusted, or structurally damaged to restore appearance.

Restores proper tension to washer mechanisms. Replaces worn, broken, or stretched springs causing binding, sagging, or uneven movement in drum suspension.

Hex washer head screw secures panels, brackets, and drum assemblies in washers. Replace rusted, stripped, or missing screws to prevent rattling.

Replaces a cracked, broken, or missing washer drum baffle. Mounts inside the drum to lift and tumble clothes during the wash cycle. Easy installation.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Washer won't spin or makes loud noises? A faulty drive motor is often the cause. Moderate DIY repair with video guide. Fixes E58 error codes.

Secures the motor housing to its mounting bracket in washers and laundry centers. Replace if screw is missing, stripped, or damaged during service.

Seals washer tub halves to prevent leaks between drum sections. Replace if leaking onto floor or between shell halves. Confirm fit with model number.

Drive belt transfers motor power to drum for tumbling and spinning. Replace when worn, stretched, or broken to restore smooth drum rotation. Verify fit.

Includes: pulley and pulley bolt.

Replacement mounting screw for washers and laundry centers. Secures components like pulleys, brackets, and panels. Replace if missing, stripped, or damaged.

Front shock absorber kit stabilizes the washer tub during spin cycles. Replace worn, loose, or broken dampers to restore smooth operation and stability.

Stabilizes the washer tub during spin cycles. Replace worn or broken rear shock absorbers to restore smooth operation and prevent drum contact with cabinet.

Secures the shock absorber to the outer tub in your washer. Replace if the pin is broken, cracked, or missing to restore proper shock mounting.

Cushion bumper for washer installation. Absorbs vibration and protects cabinet surfaces. Replace if cracked, compressed, or missing to restore proper support.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Mounting bracket secures components inside your laundry center. Replace if bent, broken, or missing to eliminate rattling and restore stability.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Fix a washer that won't drain or makes buzzing sounds during drain cycle. This pump assembly removes water from the tub. DIY-friendly repair restores draining.

Screens lint and debris from wash water as it exits the tub. Replace if damaged, missing, or clogged to restore proper draining. Verify fit by model number.

Connects the outer tub to the drain pump in front-load washers. Replace if cracked, torn, leaking, or clogged to stop water damage and restore drainage.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Pressure hose and adapter assembly that connects the air chamber to the water level sensor. Replace if tube is cracked, pinched, or leaking air.

Washer air chamber connects the water level pressure switch to the tub. Replace if cracked, kinked, or disconnected causing water level issues.

Washer hose clamp secures water inlet and drain hoses to prevent leaks. Replace if loose, cracked, or causing water drips. Verify fit with your model number.

Secures the door boot seal to prevent leaks in front-load washers. Replace if rusted, broken, or seal is loose. Verify fit with your model number.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Replacement drain hose for washing machines. Transports water from tub to household drain. Replace if cracked, kinked, leaking, or damaged from wear.

Cable tie secures wiring bundles and hoses inside your laundry center. Prevents loose routing, rubbing, and rattling noises. Replace if broken or missing.

Replacement mounting bracket that secures washer panels and components. Needed when original bracket is cracked, broken, or missing, causing loose or misaligned parts.

10-inch heating element that restores proper heat production in affected appliances. Replaces a worn or failed element to help resolve issues like no heat or unusually long cycle times. What it does:

• Generates heat so your appliance can reach normal operating temperatures.
• Common symptoms it addresses: little or no heat, longer-than-normal cycles, or intermittent heating.
• Replaces a single failed element to return consistent heating performance.

What's included: One heating element. Install notes:

• Disconnect the appliance from power before attempting any repair.
• Allow the element to cool and handle carefully to avoid bending or damaging the coil.
• Ensure the terminal connections are secure and free of corrosion; tighten or replace fasteners as needed.

NOTE: IF THERMISTOR HAS TERMINALS WIRE HARNESS HAS TO BE CHANGED PART# 137288900 PER FRIGIDAIRE

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.