Kenmore Dryer 110.6307830 (1106307830, 110 6307830) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 8009
Original Whirlpool light bulb, 40 watt.
Symptoms of needing to replace the light bulb include:
- Dimming or flickering light
- Complete lack of illumination inside the appliance
- Visible signs of damage or burnout on the bulb itself
Causes of a faulty light bulb can include normal burnout over time, electrical issues, or physical damage due to impact or vibrations.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Kenmore, Frigidaire, GE, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances.
Do-It-Yourself Stories from Customers like You
Jennair jjw9630cas double oven doors did not close all the way and the light would not go out Wayne W. • East Longmeadow , MA • February 13, 2016
I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it...
Read more
More
$18.23
- Compare At:
-
$21.69
- You Save:
-
$3.46
Genuine Whirlpool part
By: Whirlpool
Part Number: 279570
The Door Latch Kit is an OEM replacement part for Whirlpool washers. This component is responsible for securely locking the washer door during the wash cycle, preventing it from opening unexpectedly and ensuring a safe and efficient operation.
Symptoms of needing to replace the door latch kit include:
- Difficulty in closing or latching the washer door
- Door opening unexpectedly during the wash cycle
- Leaks or water seeping due to an improper door seal
- Excessive wear or damage to the latch components
Causes of a faulty door latch kit can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the door alignment or strike plate.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.
This part fixes the following symptoms
-
Door won't close
-
Shuts off too soon
-
Doesn't shut off
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Dryer door latch worn out Kathy M. • San Diego , CA • February 22, 2015
When I looked up the part number there was a handy video that popped up. I watched the video and thought "how easy!" so, I ordered that part and waited. The next day, I thought I better start to take the door off of my dryer (because that's what the video instructed, and I wanted a head start) so as I was going into the garage to get my tools, my son came in with a small package. It was the part. That came, to quote another customer, "Crazy Fast!" All the way from Kentucky to California! ...
Read more
More
$8.56
- Compare At:
-
$13.85
- You Save:
-
$5.29
Genuine Whirlpool part
By: Whirlpool
Part Number: WP691581
The Door Switch Lever is an OEM part for Whirlpool dryers. It plays a vital role in ensuring the dryer only operates when the door is securely closed by engaging with the door switch to signal the door's status.
Causes of a bad door switch lever can include normal wear and tear from repeated use, physical damage from accidental impact, or deformation from heat and humidity inside the dryer. A faulty lever can prevent the dryer from starting or stopping correctly.
Symptoms of a bad door switch lever include:
- Dryer not starting
- Dryer stopping mid-cycle
- Door not latching properly
- The dryer continuing to run with the door open
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Won't start
-
Doesn't shut off
See more...
Do-It-Yourself Stories from Customers like You
The lever to the door switch broke. Valerie M. • Rochester , NH • April 02, 2014
First, I rooked on YouTube for a video on how to fix it. The video brought me to a very helpful video with a link to your website. We have had this dryer since we bought the house 10 years ago and the thought of buying something new, that wasn't made as well was a dreaded thought. I went on the website, entered the model number of my dryer and then a search link for a parts search. Not knowing the part number, I was able to find the exact thing I needed. It was amazing and so easy! Had...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 279264
Replaces worn dryer front bearing and seal that cause squealing or scraping noise. Essential for smooth drum rotation. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Noisy & inefficient Richard M. • Indianapolis , IN • December 06, 2016
After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify...
Read more
More
$67.95
- Compare At:
-
$81.54
- You Save:
-
$13.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP18776
The Top Lock is an OEM component for Whirlpool electric and gas dryers. It secures the outer metal cabinet door during drying cycles for safety and ventilation. This lock provides a method for releasing and latching the door tightly when shut.
Symptoms of a failing top lock may include:
- Inability to fully close or properly latch the dryer door
- Accidental opening from deficient locking during operation
- Difficulty manipulating the lock due to worn or broken parts
Causes related to normal wear of moving parts through frequent use over several years. Deformation from excessive exterior impacts could also damage locking mechanisms.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Multiple problems warn parts Jeffrey C. • Severna Park , MD • April 29, 2015
Excellent! Repairs went as planned. Diagnosed problem parts on my dryer; ordered parts online thru Appliance Parts Pros; parts arrived very quick - standard ground - and parts shipped as ordered with no mistakes. Plus, they sent me a Wine voucher (my order was nearly $200). And, if you have trouble troubleshooting your appliance problem or figuring out how a part is supposed to be installed on your appliance, Appliance Parts Pros has an excellent video library to help you!
I will certainly...
Read more
More
$12.95
- Compare At:
-
$15.28
- You Save:
-
$2.33
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP98234
U-type clip nut slides onto sheet metal panels to create threaded anchor points for screws. Replace if broken, missing, or worn during repairs.
Do-It-Yourself Stories from Customers like You
Broken hinge Ronald B. • Manchester , CT • October 21, 2019
Followed the video on how to replace the hinge I also replaced the dryer top locks while I had it open
Read more
More
$11.78
- Compare At:
-
$13.90
- You Save:
-
$2.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WP660658
This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.
Do-It-Yourself Stories from Customers like You
The dryer motor stopped working. Kenneth M. P. • Saint Clair Shores , MI • December 05, 2021
I ordered a replacement motor from APP and installed it myself.
Read more
More
$10.37
- Compare At:
-
$12.44
- You Save:
-
$2.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 279220
Includes two bumpers and two locking clips. You will use one or the other depending on hole size.
Do-It-Yourself Stories from Customers like You
Gas dryer did not heat and excessive lint inside the unit James C. • New Boston , MI • July 20, 2017
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered...
Read more
More
$12.32
- Compare At:
-
$14.54
- You Save:
-
$2.22
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3394508
Supports the front drum edge for smooth, quiet rotation. Replace when worn to stop scraping noises or drum wobble. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Drum rear seal worn front bearing same Joseph M. • Conshohocken , PA • February 20, 2015
Replace parts worn i repair appliance for60 years i am79
Read more
More
$60.52
- Compare At:
-
$71.41
- You Save:
-
$10.89
Genuine Whirlpool part
By: Whirlpool
Part Number: W11613302
Heat-resistant fiberglass gasket seals your oven door perimeter to maintain consistent temperatures. Replace when worn, frayed, or flattened to restore efficiency. Verify fit by model number.
More
$35.57
- Compare At:
-
$42.33
- You Save:
-
$6.76
Genuine Whirlpool part
By: Whirlpool
Part Number: WP297092
This small retaining clip secures the door hinge in place so the door opens and closes smoothly and stays properly aligned. Replacing a worn or missing clip helps restore reliable hinge support and consistent door operation.
- Retains the hinge/hinge pin to prevent shifting or separation
- Helps maintain door alignment to avoid rubbing, sagging, or binding
- Replaces a clip that is bent, cracked, corroded, or missing
- Common signs it's needed: loose or wobbly door, difficulty closing, misaligned door, visible damaged/missing clip
What's included: 1 hinge clip Install notes:
- Unplug the appliance and, if applicable, remove items from the door to reduce weight
- Support the door before working on the hinge
- Remove any hinge cover/fasteners, swap the clip, and ensure it seats fully
- Reassemble and check door alignment and smooth operation
Do-It-Yourself Stories from Customers like You
Dryer no start George Larry B. • Niceville , FL • November 19, 2019
Removed and replaced start switch then motor, no joy. removed the timer for disassembly, found bad contact. soldered contact to the spring tab and assembled and installed the timer. All good now.
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8066217
Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.
Do-It-Yourself Stories from Customers like You
Would not spin Andrew M. • Long Island City , NY • December 18, 2015
Replaced belt and idler arm, just to be safe.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP356418
This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.
- Provides fastening with a built-in washer for even clamping and retention
- Replaces missing, stripped, or corroded hardware
- Helps address loose panels/handles and vibration or rattle noises
- Supports proper alignment of covers, brackets, and trim
What's included: 1 screw-washer assembly Install notes:
- Disconnect power and shut off water or gas (as applicable) before servicing
- Match to the original fastener; location and quantity in your model's parts diagram
- Start threads by hand to avoid cross-threading; tighten with the correct driver
- Do not overtighten; replace other severely rusted or damaged fasteners in the same area
Do-It-Yourself Stories from Customers like You
Timer/control failed Gilbert G. • Lansing , IL • July 09, 2018
Replaced timer control unit, first time doing this.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP691371
This fan belt transfers motor power to the appliance fan so the fan can move air as designed. Replacing a worn or broken belt restores proper airflow and helps reduce noise or overheating from reduced circulation. What it does:
- Wraps around the motor and fan pulley to drive the fan blade
- Restores fan rotation when a cracked, stretched, or broken belt prevents normal operation
- Helps return proper airflow for cooling and ventilation, reducing stress on the motor
- Reduces unusual noises caused by slipping or damaged belts
What's included: One replacement fan belt Install notes:
- Disconnect power (unplug or switch off breaker) before starting any repair
- Remove access panels as needed to reach the motor and fan assembly; note belt routing before removal
- Fit belt to motor pulley and fan pulley, ensuring correct alignment and tension per the appliance design
- Reassemble panels, restore power, and run a short test to verify normal fan operation; discontinue use if abnormal noise or vibration persists
Do-It-Yourself Stories from Customers like You
Broken dryer fan belt Scott L. • Clinton Township , MI • August 30, 2014
Order and replace
Read more
More
$54.95
- Compare At:
-
$65.81
- You Save:
-
$10.86