Kenmore Washer Dryer Combo 417.99464100 (41799464100, 417 99464100) Parts
Genuine Frigidaire part
By: Frigidaire
Part Number: 3204267
Dryer won't heat or shows E64 error? High-limit thermostat cuts power if overheating occurs. Moderate DIY fix with our video guide and instructions.
This part fixes the following symptoms
-
Shuts off too soon
-
Too hot
-
Takes too long to dry
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
The dryer did not heat! Linda R. • La Jolla , CA • November 30, 2014
My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the...
Read more
More
$57.62
- Compare At:
-
$68.57
- You Save:
-
$10.95
Genuine Frigidaire part
By: Frigidaire
Part Number: 131825900
Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.
This part fixes the following symptoms
-
Marks left on clothes
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Dryer would not turn on Kathie R. • Burlington , WI • January 15, 2016
The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible.
Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem.
Next step was to...
Read more
More
$10.71
- Compare At:
-
$12.74
- You Save:
-
$2.03
Genuine Frigidaire part
By: Frigidaire
Part Number: 134511600
Drive belt connects motor to drum for wash and spin cycles. Replace if washer won't spin, clothes stay wet, or you smell burning rubber. Verify fit.
This part fixes the following symptoms
-
Spins slowly
-
Burning smell
-
Pumps but will not spin
-
Will not agitate
See more...
Do-It-Yourself Stories from Customers like You
Noisey bearing on spin cycle Neal G. • Klamath Falls , OR • February 14, 2016
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple.
Read more
More
$23.61
- Compare At:
-
$28.10
- You Save:
-
$4.49
Genuine Frigidaire part
By: Frigidaire
Part Number: 131658800
Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.
This part fixes the following symptoms
-
Door won't close
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Drum stopped turning loud 60 hz hum from motor James S. • Winchester , TN • November 03, 2018
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts.
Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum...
Read more
More
$54.25
- Compare At:
-
$65.10
- You Save:
-
$10.85
Genuine Frigidaire part
By: Frigidaire
Part Number: 5308027429
The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets
Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.
Symptoms of a bad high temperature adhesive include:
- Components or parts becoming loose or detached
- The adhesive becoming brittle or cracked
- Inability to properly bond surfaces exposed to high heat
- Visible deterioration or peeling of the adhesive
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
This part fixes the following symptoms
-
Marks left on clothes
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Clothes getting stuck in front of dryer then later on a grinding and loud noise when spinning Michael G. • Chicago , IL • August 23, 2020
I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose."
The cause of the scraping and loud...
Read more
More
$52.68
- Compare At:
-
$62.69
- You Save:
-
$10.01
Genuine Frigidaire part
By: Frigidaire
Part Number: 3204405
Enables smooth drum rotation in your washer. Replace if you hear loud roaring or whirling noises during spin cycle. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Noisey bearing on spin cycle Neal G. • Klamath Falls , OR • February 14, 2016
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple.
Read more
More
$78.78
- Compare At:
-
$93.75
- You Save:
-
$14.97
Genuine Frigidaire part
By: Frigidaire
Part Number: 5308002401
The Spin Bearing Washer is an OEM part for Frigidaire washing machines. Situated inside the transmission housing, this thin metal washer acts as a subsurface support for the belt pulley bearing. The spin-bearing washer facilitates smooth, balanced rotation essential for agitated and spun wash cycles.
Causes of a bad spin-bearing washer include wear and fatigue from years of successive rotations, potentially allowing excessive movement between housing components.
Symptoms of a bad spin-bearing washer involve:
- Vibration or shaking noises coming from inside the washer cabinet
- Belt slippage wasting energy by inefficiently spinning loads
- Increased friction resulting in longer cycle times for spins
- Failure of belts or other components from unsupported bearing
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
Do-It-Yourself Stories from Customers like You
Noisey bearing on spin cycle Neal G. • Klamath Falls , OR • February 14, 2016
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple.
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Frigidaire part
By: Frigidaire
Part Number: 134190200
Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
-
Will not fill with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
The washer was filling very slow especially cold water. Wayne S. • Oakland , MD • February 10, 2023
This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent...
Read more
More
$103.95
- Compare At:
-
$124.74
- You Save:
-
$20.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303207102
Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.
Do-It-Yourself Stories from Customers like You
Frigidaire dryer door would not stay closed Carolina L. • Miami , FL • September 08, 2015
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch.
I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to...
Read more
More
$28.95
- Compare At:
-
$34.45
- You Save:
-
$5.50
Genuine Frigidaire part
By: Frigidaire
Part Number: 131724301
The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.
Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.
Symptoms of a bad drum bearing bracket include:
- Excessive vibration or shaking during operation
- Loud grinding or scraping noises
- The dryer drum not spinning properly or at all
- Premature wear of the drum bearing
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer drum would not turn J Kent I. • Anderson , IN • February 22, 2019
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros.
Read more
More
$9.63
- Compare At:
-
$11.56
- You Save:
-
$1.93
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303281019
Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.
Do-It-Yourself Stories from Customers like You
Dryer drum would not turn J Kent I. • Anderson , IN • February 22, 2019
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros.
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Frigidaire part
By: Frigidaire
Part Number: 131168200
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
- Fastens components to frames, brackets, and covers
- Replaces missing, damaged, or rusted screws
- Helps reduce looseness, vibration, and rattling noises
- Restores proper alignment of panels and assemblies
What's included: One screw
- Disconnect power before servicing; shut off gas/water if applicable
- Start the screw by hand to avoid cross-threading; use the proper driver
- Tighten snugly—do not overtighten to prevent stripping metal or plastic
Do-It-Yourself Stories from Customers like You
Grill on air duct had an item melt on to it and partially block air flow Charles C. • Orchard Park , NY • November 25, 2017
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube.
I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to...
Read more
More
$19.95
- Compare At:
-
$23.94
- You Save:
-
$3.99
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303281020
For a complete drum bearing and shaft kit order 5303281153.
Do-It-Yourself Stories from Customers like You
Dryer drum would not turn J Kent I. • Anderson , IN • February 22, 2019
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros.
Read more
More
$12.95
- Compare At:
-
$15.28
- You Save:
-
$2.33
Genuine Frigidaire part
By: Frigidaire
Part Number: 131302800
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
- Fastens the drum baffle/lifter (vane) to the rotating drum
- Helps maintain proper tumble and load turnover
- Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
- Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes
What's included: One screw
- Disconnect power before servicing; shut off gas
- Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
- Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
- Start all screws before final tightening to seat the baffle evenly
Do-It-Yourself Stories from Customers like You
The pump hose had a tear in it and the water hoses were in bad shape Steven V. • El Cerrito , CA • September 21, 2014
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy
Read more
More
$17.95
- Compare At:
-
$21.54
- You Save:
-
$3.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303321319
The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.
The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.
Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.
Symptoms of needing Touch Up Paint include:
- Visible scratches or chips on the appliance's surface.
- Areas of rust or corrosion that need to be covered after treating the rust.
- The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.
Do-It-Yourself Stories from Customers like You
Small chip in the frigereator Julia J. • Maple Grove , MN • October 03, 2015
Quick touch up. The paint worked great. Packaged with a brush like nail poliish
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Frigidaire part
By: Frigidaire
Part Number: 137107000
Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.
Do-It-Yourself Stories from Customers like You
Leaking washer tub Hugh S. • Miami , FL • June 25, 2016
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off...
Read more
More
$20.33
- Compare At:
-
$24.19
- You Save:
-
$3.86