Kenmore Washer Dryer Combo 110.6109807 (1106109807, 110 6109807) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22002263
Illuminates the dryer drum for better visibility when loading and unloading. Replace when bulb burns out or fails to light. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Squeaky noise and not fully drying David H. • Santa Clarita , CA • September 20, 2019
Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking.
I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was...
Read more
More
$15.55
- Compare At:
-
$18.50
- You Save:
-
$2.95
Genuine Whirlpool part
By: Whirlpool
Part Number: 285452A
Filters debris from water entering your washer and seals the hose connection. Replace if water fills slowly or screens are clogged. Confirm fit by model.
Do-It-Yourself Stories from Customers like You
Water puddle on floor at front left corner; glass lid dripping water on soap dispenser from splashing and leaking down side panel onto floor Ronnie M. • Phoenix , AZ • June 25, 2019
As a Mechanic, I did the common sense approach:
INITIAL OBSERVATIONS & CHECKS:
- Unplug Machine & check inlet water hose connections for leaks and signs of hose failure;
- Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows...
- Inspect...
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596669
The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.
Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Leaks at the hose connection points
- Hoses slipping off the connections
- Visible rust or damage on the clamp
- Reduced appliance efficiency due to leaks
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not stop filling with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
My washing machine smelt horrible Bryan W. • Ogdensburg , NY • August 20, 2018
First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available....
Read more
More
$7.48
- Compare At:
-
$8.98
- You Save:
-
$1.50
Genuine Whirlpool part
By: Whirlpool
Part Number: WP18776
The Top Lock is an OEM component for Whirlpool electric and gas dryers. It secures the outer metal cabinet door during drying cycles for safety and ventilation. This lock provides a method for releasing and latching the door tightly when shut.
Symptoms of a failing top lock may include:
- Inability to fully close or properly latch the dryer door
- Accidental opening from deficient locking during operation
- Difficulty manipulating the lock due to worn or broken parts
Causes related to normal wear of moving parts through frequent use over several years. Deformation from excessive exterior impacts could also damage locking mechanisms.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Multiple problems warn parts Jeffrey C. • Severna Park , MD • April 29, 2015
Excellent! Repairs went as planned. Diagnosed problem parts on my dryer; ordered parts online thru Appliance Parts Pros; parts arrived very quick - standard ground - and parts shipped as ordered with no mistakes. Plus, they sent me a Wine voucher (my order was nearly $200). And, if you have trouble troubleshooting your appliance problem or figuring out how a part is supposed to be installed on your appliance, Appliance Parts Pros has an excellent video library to help you!
I will certainly...
Read more
More
$12.95
- Compare At:
-
$15.28
- You Save:
-
$2.33
Genuine Whirlpool part
By: Whirlpool
Part Number: 285352
Prevents oil leaks from your washer's gearcase and keeps internal components lubricated. Replace if you notice oil pooling under the machine.
Do-It-Yourself Stories from Customers like You
Not spinning clothes dry Marjorie S. • Lansing , NC • December 16, 2017
Replaced clutch assembly, gearcase input shaft seal and motor coupler. When I disassembled the washer I realized the shaft seal on the top of the gearcase was leaking and not the input shaft seal. So had to order more parts before I could finish this job. Altogether I replaced agitator dogs, both seals on the gearcase, the clutch assembly and the motor coupler.
Agitator dogs replacement is a very easy job, no tools required, takes less that 5 minutes and made a huge difference with how well...
Read more
More
$51.62
- Compare At:
-
$61.43
- You Save:
-
$9.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP285655
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Water leaks around the hose connection points
- The hose slipping off the fitting
- Visible rust or wear on the clamp
- Difficulty in tightening the clamp to secure the hose
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Syphonbreak was leaking James O. • Bryant , AL • September 04, 2015
We ordered parts from appliance parts pros and I fixed it.
Read more
More
$9.63
- Compare At:
-
$11.46
- You Save:
-
$1.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP353244
Washer overfilling or not filling properly? A damaged pressure switch hose prevents accurate water level sensing. Easy 15-minute DIY fix with video.
Do-It-Yourself Stories from Customers like You
My kenmore washer model 11029828801 was agitating during the fill cycle and the tub would only partially fill also at the end of the spin cycle rinse water was spraying in resoaking the clothes Jay S. • Hammond , IN • February 07, 2017
I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new...
Read more
More
$53.21
- Compare At:
-
$63.32
- You Save:
-
$10.11
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP616099
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
- Tightens around a hose and fitting to maintain a secure seal
- Helps stop drips, seepage, or loose connections
- Common fix when you see moisture around a hose joint
- Useful if a clamp is rusted, stretched, or no longer holding tension
What's included: One hose clamp. Install notes:
- Unplug power and shut off water (if applicable) before servicing
- Note clamp position/orientation before removal
- Use appropriate screwdriver or nut driver to tighten evenly
- Do not overtighten—ensure a snug, leak-free seal without damaging the hose
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
$9.95
- Compare At:
-
$11.59
- You Save:
-
$1.64
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP488163
Replacement screw that secures panels, brackets, and trim to appliance cabinets. Restores reliable hold when original hardware is stripped or missing.
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP691371
This fan belt transfers motor power to the appliance fan so the fan can move air as designed. Replacing a worn or broken belt restores proper airflow and helps reduce noise or overheating from reduced circulation. What it does:
- Wraps around the motor and fan pulley to drive the fan blade
- Restores fan rotation when a cracked, stretched, or broken belt prevents normal operation
- Helps return proper airflow for cooling and ventilation, reducing stress on the motor
- Reduces unusual noises caused by slipping or damaged belts
What's included: One replacement fan belt Install notes:
- Disconnect power (unplug or switch off breaker) before starting any repair
- Remove access panels as needed to reach the motor and fan assembly; note belt routing before removal
- Fit belt to motor pulley and fan pulley, ensuring correct alignment and tension per the appliance design
- Reassemble panels, restore power, and run a short test to verify normal fan operation; discontinue use if abnormal noise or vibration persists
Do-It-Yourself Stories from Customers like You
Two broken belts for lady kenmore (52 years old & still running great) Darwin M. • Toms Brook , VA • May 26, 2017
Obtained the replacement belts from AppliancePartsPros.com and installed on dryer.
Read more
More
$54.95
- Compare At:
-
$65.81
- You Save:
-
$10.86
Genuine Whirlpool part
By: Whirlpool
Part Number: WP76314
Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A
Do-It-Yourself Stories from Customers like You
Bad fill hose. Rick D. • Maywood , NJ • January 05, 2022
Replaced hose and washers.
Read more
More
$34.75
- Compare At:
-
$41.00
- You Save:
-
$6.25