Parts for Bosch SRV53C13UC/01: Pump Assembly Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.

Replaces cracked or brittle dishwasher hose connecting the sump to the water inlet valve. Includes 2 o-rings. Essential for preventing leaks during pump replacement or routine maintenance.

O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.

Replacement water level control cover for dishwashers. Snaps over the water level control assembly. Order a new cover if yours is broken, cracked, or missing.

O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.

Fix a dishwasher that won't fill with water by replacing the water inlet valve. This part controls water flow into your dishwasher during wash cycles.

The Pressure Chamber is an OEM part for Bosch dishwashers. This part is responsible for monitoring and controlling the water level within the dishwasher. It operates by sensing the pressure exerted by the height of the water in the tub and ensures that the dishwasher fills with the correct amount of water for optimal cleaning performance.

Causes for replacement may involve wear and tear over extended use, mineral buildup affecting the switch’s sensitivity, or electrical faults leading to inconsistent performance.  

Symptoms of a failing Pressure Chamber include:

• Overfilling or underfilling of the dishwasher, which can lead to inadequate cleaning or potential water damage.
• Unexpected changes in the wash cycle, such as sudden stops or pauses.
• The dishwasher not starting a wash cycle due to incorrect water level readings.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Dishwasher won't fill or keeps overfilling? The float switch detects water levels for proper filling and draining. Accessible repair in under 30 minutes.

O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.

Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.

Seals the dishwasher sump to prevent water leaks during wash cycles. Replace if you notice leaking at the base or constant drain pump operation.

Secures the sump assembly to the tub, preventing leaks and movement. Replace if worn, cracked, or if you notice water leaking from the base of your dishwasher.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Secures the hose between pump and heater in your dishwasher. Replace if loose, damaged, or causing leaks. Confirm fit with your model number.

Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Fix poor cleaning and weak spray arms with this circulation pump motor. Powers water through your dishwasher's wash system. Moderate DIY repair.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Pump housing cover for dishwashers. Replaces cracked, broken, or missing covers that protect the pump assembly. Installs over the pump mechanism.

Seals connection between pump and sump to prevent leaks during wash cycles. Replace if water pools under dishwasher or pump noise occurs.

Fix dishwasher not draining or foul odors with a new check valve. Prevents dirty water backflow into clean dishes. DIY-friendly repair in 1-2 hours.

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Dishwasher salt funnel guides water softener salt into the reservoir without spills. Replace if cracked or lost to maintain proper salt loading.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.