Scott February 11, 2013 for Model Number mah8700aww When I called maytag and priced the control board for my washer they asked for the first 2 digits of my serial number for the correct part. This site does not ask that so I need the part number for a control board. My serial number is 11275315gp. Also, there is no picture and according to the part diagram I assume it is #5 and it says control board sensor, does this include the whole piece, sensor and control board both? Mine has a black case with the computer board covered in a gel so not sure I can replace it if its not together as an assy. Thanks for any help.
1 Answer Scott, according to the model/serial number of your washer the replacement board is part number 34001494. This includes the control board, motion sensor w/ bracket and the wire harness. Thanks! Read More...
Nef November 05, 2012 for Model Number mah8700aww So my washer also shows E3 code. I checked the drum to make sure it moves freely. I put washer in self test and it will go to full spin. I also pulled control board and checked ohm reading for motor at plug cn9. my readings are all above 3 ohms. Good or bad? I dont understand why motor will spin in self test but not under normal conditions. Is motor bad or is control board bad?
1 Answer Hello Nef. Based on the information you provided, it sounds like the control board is the issue, not the motor. Read More...
Jay D October 17, 2012 for Model Number MAH8700AWW sn 10198171GL Can you tell me which model replacement control board is correct for my model and serial no. (MAH8700AWW sn 10198171GL) Thanks, Jay
1 Answer Hello Jay. Based on the model and serial provided, 34001494 is the correct control board. Read More...
Rusty C. May 01, 2012 for Model Number MAH8700A I have a Maytag MAH8700 front load washer. When I try to do a load of laundry I get an 3E error code. A service repair man already replaced the motor. Do you think that it is the circuit board control panel? If so what is the part number? Thank you
1 Answer Hello Rusty. If the motor is new, you will need to check and see if the wiring is good on the washer. If it is good, then it could have a bad control board 34001494 on the unit. Make sure there are no broken wires going to the motor, and the connections on the wires are good. Read More...
Ssg Noyes February 26, 2012 for Model Number MAH8700AWW serial # 1019163GL E3 code... Did all checks & all were good, Quick test ok, I assume I need a Control Board. Is part # AP4044369 the correct part ?
1 Answer Hello SSG. Yes, based on the model and serial numbers you provided, 34001494 is the correct control board for the unit. Hope this helps. Read More...
Steve B. February 23, 2012 for Model Number MAH8700AWW My washer serial number is 10298108GE. According to your website, this is the part that I need...AP4044368 (I show an SR code every once in awhile). Why is the picture on your website show the board as black in color, but in other repair sites, they show it as a white colored board for the series 10? Also, sometimes I see the boards have other parts along like the harness, but this doesn't. Just want to make sure I get the correct one.
1 Answer Steve, according to your model/serial number the control board 34001494 is the correct part used on your appliance. We have an older picture of this item on our site and it is currently in the process of being updated. Thanks! Read More...
Peter February 07, 2012 for Model Number mah8700aww serial #11264997gp What is the correct control board part # for maytag neptune with the above serial #?
1 Answer Hello Peter! According to the model/series combo you will use control board part number 34001494. Thanks! Read More...
Marco January 06, 2012 for Model Number MAH8700AWW My washer sometimes wash and sometimes appears a code 3e.
1 Answer Hello Marco. There have been problems with the motor wire harness connector on these washers. The problems are either a loose or bent terminal in the molex connector. Unplug the connector and tug on each wire. If a wire comes loose from the plug, bend the locking tab up. If a locking tab is not properly seated in the plug connector, the terminals will not fully engage as the connector is plugged into the motor. Another manifestation of this problem is that one of the terminals may be bent. Inspect the terminals on the motor side of the connector. Straighten any bent terminals if they exist. Recheck the harness side of the terminal block if any bent terminals are found. Bent terminals can indicate a problem with the locking tab inside the plug. If the connections are good, you will need to replace the motor WP34001437. Hope this helps. Read More...
Shane December 29, 2011 for Model Number mah8700aww I am getting an "Sr" error code but the washer seems to be working fine. Which Control Board do need based on a serial number of 18475AYC47005Z?
1 Answer Hello Shane. Based on the serial number, 34001498 is the correct control board. Hope this helps. Read More...
Alex December 16, 2011 for Model Number MAH8700AWW What is the correct control board part number for Maytag Neptune model MAH8700AWW Serial # 11278438GP? Thank you.
1 Answer Hello Alex. Based on the model and serial number you provided, 34001494 is the correct control board for the washer. Hope this helps. Read More...