Ken December 06, 2019 for Model Number WDF560SAFM0 when you start the cycle, sometimes it comes on and sometimes it doesn't but the lights on the control panel are on.
Juanita December 04, 2019 for Model Number Whirlpool quiet partner IV dishwasher The control pannel on my dishwasher has flashing lights but it won't work. I believe it is the control panel but cannot determine the part number for replacement.
1 Answer Juanita, We will need your model number to help you find the right parts for your unit. Please post another question with all your info included thank you. The flashing lights will be the error code and is dependent upon the model to check the code. Read More...
Hilda. (Again) October 26, 2019 for Model Number DU1055XTVQD I have the model # now so wanted to confirm the info you gave me yesterday. Is the part I need AP2920798? And is the replacement fairly straightforward? This is a great service - Thank you so much!
1 Answer Hello Hilda, the control panel for your model number is part number WP3385731, however it is no longer available in white anymore. Hope this helps! Read More...
Hilda October 25, 2019 for Model Number 8575637 The lights on the panel have started flashing randomly when I start the washer. I can't turn them off by pressing or control their sequence. Surprisingly, the dishes have been coming out clean despite the light show! I don't know which cycle is being run and can no longer select the delay feature or other options. I'm not sure of the model #, the one I gave is on the label next to the Energy Star symbol. Can you help?
1 Answer Hello Hilda, the model number given does not show as a valid model number. However, the symptom you are describing does sound like a faulty keypad/control panel. Read More...
Michael June 27, 2019 for Model Number KUDS24SE KITCHEN AID I TRIED TURNING THE BREAKER OFF AND STILL NOTHING. iF i HIT THE START BUTTON IT LIGHTS UP BUT NOTHING IS HAPPENING. WHATS NEXT TO TRY?"
1 Answer Hello Michael, the keypad assembly is faulty. The repair part is WP9743241 Switch Panel. Read More...
Michael June 26, 2019 for Model Number kitchen aid KUDM24SE We have had this unit Kitchen Aid KUDM24SE for 12 years now. Two nights ago I started it using the time delay function and it stopped after the prewash rinse cycle. Ive tried to reset the unit and nothing. What should I try next?
1 Answer Michael, We will need a little more info to help you out. What state is the unit in? ex. unit is dead or lights flashing on the display and will not respond. Will it do anything at all like drain or fill only. Try killing power to the unit from the breaker box for a couple of minutes and see if anything changes. Please post another question with all your info included thank you. Read More...
Barbara W November 06, 2018 for Model Number Whirlpool FSE090512 The light comes on some of the buttons, but pushing start is not working. This has happen before, but the label on the inside of the dishwasher has come off, so the instructions are gone. I know I need to hold down one of the buttons and reset the panel, but I don't know which one to hold down. Thank you for any help
1 Answer Barbara, The model number listed is not coming up as being a valid model. Try disconnecting power to the unit for 15 minutes and if this does not correct the issue then it sounds as though the control panel may need to be replaced. Read More...
Gary W June 20, 2018 for Model Number WDF510PAYW8 Water will not heat above faucet temperature. No heat during drying cycle. I have checked resistance on heating coil. Shows good. Hi temp switch was disconnected but checked ok. Reconnected it. Shows good. Appliance repair guy told my wife the drain wasn't right. Unit run fine until about 6 months ago. Can't believe drain was the problem. Water that is in machine is just drops where it didn't dry. Could it need a new switch unit? Any help would be appreciated. Can this switch unit be returned if its not the problem?
1 Answer Gary, This issue would most likely be caused by a faulty control board which will be part number W10804121. You will want to put the unit into a heat cycle and check to see if there is 120 vac getting to the heater. If there is not then the control board will be the most likely cause. Read More...
Jeff February 04, 2018 for Model Number DU1145XTPB6 My Whirlpool dishwasher's clean light keeps blinking. It will not run any of the cycles. Would it be the control panel?
1 Answer Hello Jeff. Control is programmed to stop the current cycle and not allow any further cycles if it suspects a faulty heater (no temperature increase detected in heated intervals). Control blinks the Clean LED 7 times in repetitive fashion and disables the Start/Resume key until cleared. Running Diagnostics clears the control and allows it to operate again. If heating problem is not corrected though, the control will stop running again on next cycle. Read More...
Julie November 29, 2017 for Model Number dtw720padm Dishwasher is just over 3 years old. The water is not spraying the dishes. I have cleaned the filter and I checked the arms. There are no clogs. I hear the water filling and the pump pumps the water out. So I am thinking it is not a water or pump issue. What else could it be? It has honestly only been used for 2 out of the 3 years.
1 Answer Julie, This issue will most likely be caused by a faulty diverter motor which would be part number W10537869. Read More...