Range Hood Damper & Related

The Run Capacitor is an OEM part for GE refrigerators. It plays a crucial role in the refrigerator's cooling system by providing the necessary start and run voltage to the compressor. Without a properly functioning run capacitor, your refrigerator may struggle to maintain the desired temperature, leading to spoiled food and inefficient energy use.

Causes of a bad run capacitor include electrical surges, wear and tear over time, or overheating due to a malfunctioning refrigerator compressor or poor ventilation.

Symptoms of a bad Run Capacitor include:

• The refrigerator compressor fails to start.
• Unusual humming noises coming from the refrigerator.
• The refrigerator cycles on and off more frequently than normal.
• A noticeable increase in energy consumption as the refrigerator struggles to maintain the proper temperature.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Backdraft damper flap for range hood exhaust outlet. Opens during venting, closes when off to block drafts and pests. Replace if cracked or broken.

A duct kit designed to route a dryer's exhaust safely to the household vent system, restoring proper airflow and helping the dryer vent effectively when the original ducting is damaged or missing. What it does:

• Channels hot, lint-laden exhaust from the dryer to the exterior vent to reduce indoor heat and moisture.
• Replaces crushed, torn or disconnected ducting that can cause poor drying performance.
• Use when you notice longer dry times, excess heat or lint buildup near the dryer, or backdrafting from the vent.
• Helps maintain proper vent airflow when installed and secured per manufacturer and local code requirements.

• Disconnect electrical power (and gas supply for gas dryers) before installing or servicing venting components.
• Follow the appliance manufacturer's installation instructions and local building/venting codes for diameter, length and material.
• Avoid crushing, kinking or sharp bends in the duct; secure joints with approved clamps or foil tape and check for leaks.

Backdraft damper flap for range hood vent systems. Opens to release exhaust, closes to block outside air. Replace if cracked, broken, or missing.

Extends your range hood's duct cover chimney to fit taller ceilings. Replace a damaged, bent, or missing extension for a polished, finished look.

Installation kit for range hoods. Includes mounting hardware and adapters needed to install your vent hood. Replace missing or damaged components.

Exterior chimney cover that conceals ductwork and mounting hardware on chimney-style range hoods. Replace if cracked, dented, or discolored.

Exterior cover that finishes and protects your range hood's vertical duct area. Replaces cracked, damaged, or missing chimney covers for a clean look.

Chimney extension cover for range hoods. Extends ductwork concealment for higher ceiling installations. Replace if dented, scratched, or missing.

Replaces the vent flap in your range hood exhaust system. Install when the original damper is cracked, broken, or missing to restore airflow control.

Replacement transition duct with integrated damper for range hoods. Connects ventilation system components. Needed when original is cracked or damaged.

Replacement shaft collar for range hood fan assemblies. Centers and stabilizes the rotating shaft to prevent wobbling and friction. Order today.

Upper chimney section for range hoods. Covers the ductwork between the hood and ceiling. Replace if damaged, dented, or missing during installation.

This factory replacement plate provides a rigid, stable mounting surface inside your unit. Replacing a bent or damaged plate helps keep internal components securely positioned and operating smoothly.

• Supports and locates attached components for correct fit and function
• Helps maintain alignment to reduce rubbing, vibration, or rattling noises
• Restores secure mounting when the original plate is bent, cracked, or missing
• Direct-fit replacement built to match the original footprint

• Disconnect power at the breaker before servicing
• Wear cut-resistant gloves; metal edges can be sharp
• Support attached parts and transfer any brackets or hardware from the old plate
• Tighten fasteners evenly before restoring power

Upper vent cover for range hoods that replaces cracked, dented, or discolored chimney covers. Restores finished appearance and protects ductwork.