Parts for Kitchenaid KSSC36QMS03: 10 - Refrigerator Door Parts

Replace your refrigerator water filter every 6 months for clean, fresh-tasting water and ice. Simple twist installation. Verify fit with your model number.

Outer door panel for your refrigerator. Replaces cracked, dented, or discolored exterior panels. Restores the appearance of your fridge door.

Replacement hinge leaf assembly for refrigerator doors. Restores proper door alignment when original hinge is worn, damaged, or causing door sag.

The Screw is an OEM part for Whirlpool refrigerators. This screw plays a small but important structural role, securely fastening the refrigerator door hinges in place.

Causes of a bad screw include normal wear and tear, repeated door opening/closing stress, or accidental damage during cleaning or servicing of the hinge area.

Symptoms of a bad hinge screw include:

• Loose or sagging door that does not close or seal properly
• Increased vibration or noise from the hinge area
• Difficulty opening/closing the door smoothly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is a direct replacement kit sold as a single pack to restore the original function of the listed Whirlpool assembly. It provides a like-for-like part so your appliance can operate as intended. What it does

• Replaces the failed factory component referenced by Use 2256389 / 2302878
• Restores the specific mechanical/electrical function of the original assembly
• Helps address common symptoms such as failure of the related cycle, intermittent operation, or no response from the affected subsystem
• Provides a one-for-one swap when the original part is damaged or worn

• One replacement kit

• Disconnect power and water before beginning any service
• Follow the original equipment manufacturer's instructions and use proper tools
• Handle electrical connectors and small parts carefully to avoid damage

This rail secures and guides the washer lid, restoring proper lid alignment and smooth opening/closing. Replaces a worn, cracked, or loose lid rail to reduce rattling and prevent the lid from catching during use. What it does:

• Provides a stable mounting surface for the washer lid so it opens and closes evenly
• Guides lid movement and helps prevent misalignment or binding
• Reduces noise and rattling caused by a loose or damaged rail
• Helps keep the lid seated correctly to prevent accidental gaps or snags

• Typical install requires removing the top or accessing the lid hinge area; retain original fasteners unless replacements are provided
• Disconnect power to the appliance before starting work to avoid injury

Seals your refrigerator utility bin to contain contents and prevent moisture transfer and odors. Replace if bin feels loose or leaks occur. Confirm fit with your model number before ordering.

Magnetic door gasket creates an airtight seal to keep cold air in and moisture out. Replace when worn to restore energy efficiency and temperature control.

Stainless steel screw that secures the back panel to the side panel of your dryer cabinet. Replace if screw is stripped, missing, or corroded.

Positions and supports the upper edge of your refrigerator door to maintain proper clearance and alignment. Replace if cracked, worn, or missing.

10-24 x 1/2 inch mounting screw for securing appliance panels, handles, brackets, and internal components. Replace lost, stripped, or damaged screws.

Left-hand endcap trim anchors the rail for refrigerator bins and shelves. Replace this bracket if cracked, broken, or missing to restore proper support.

Right-hand end cap that secures the refrigerator door bin trim. Replace this plastic trim piece if cracked, broken, or missing to restore a flush fit.

Replace a cracked, broken, or missing utility door bin for the center position of your refrigerator door. Restores organized storage for condiments.

Replaces the small hinged cover on your refrigerator door's dairy or utility bin. Install when original door is cracked, broken, or missing.

Cantilever door bin mounts on inner door rails to hold bottles, jars, and condiments. Replace cracked, broken, or missing bins to restore organized storage.

Secures refrigerator door shelf bins in place for easy removal during cleaning. Replace if cracked, broken, or missing to restore proper bin engagement.