Parts for Kitchenaid KFIS27CXWH3: 03 - Refrigerator Liner Parts

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

This electronic control board is the appliance's central command module, managing power and timing to motors, valves, heaters, and sensors. Replacing a failed board restores consistent operation and responsive controls when the original becomes intermittent or unresponsive.

• Directs and times appliance operations based on user selections and sensor feedback
• Switches power to loads via relays/triacs to run motors, valves, heaters, and fans
• Monitors inputs and stores fault data; may trigger error codes or indicator lights
• Typical failure signs: won't start or run, dead/blank display, unresponsive controls, stops mid-cycle, random beeping/error codes

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Use ESD protection and handle the board by its edges to avoid static damage
• Photograph wiring and transfer connectors one at a time; ensure all locks are fully seated
• Follow the model's tech sheet/service manual for any required setup, diagnostics, or calibration after installation

Fix leaks or restore water flow to your dispenser and ice maker. This refrigerator water tank reservoir holds and delivers water throughout the system.

No water to ice maker or slow dispenser flow? This dual inlet valve controls water to both. Moderately easy DIY repair restores proper filling.

Bypass cap replaces water filter when filtration isn't needed. Install when using RO system or preferring unfiltered water. Confirm fit with your model.

Interior lights staying on or not working? This door switch controls refrigerator lighting and functions. Moderate DIY repair with video guide available.

Flip-down door won't stay closed or open smoothly? This push latch secures compartment doors with a spring-action catch. Simple DIY fix in minutes.

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

Fridge not cold enough but freezer works fine? A faulty damper control prevents cold air from reaching the fresh food section. Moderate DIY repair.

Refrigerator not cooling evenly or running too warm? A worn blower wheel disrupts airflow, causing uneven temperatures and poor cooling performance.

This grommet isolates the refrigerator's fan motor from its mounting bracket to reduce vibration and noise while keeping the motor secure. Replacing worn or missing grommets helps stop rattles and prevents the fan blade from rubbing.

• Cushions the fan motor to maintain proper alignment and clearance
• Absorbs vibration to help reduce humming, buzzing, or rattling sounds
• Helps keep the motor stable so the blade doesn't contact the shroud
• Common signs of failure include excess vibration, noise, or a loose fan motor

• Disconnect power to the refrigerator before servicing
• Access the fan motor area (rear of unit or inside the freezer, depending on model) and support the motor
• Remove mounting hardware and seat the new grommet fully in the bracket/mount
• The fan blade spins freely with even clearance before reassembling and restoring power

Note: The Fan Motor with Harness also includes the Defrost Thermostat and Thermistor.

The Evaporator Fan Motor is an OEM part for Whirlpool refrigerators. This motor is responsible for circulating cold air throughout the refrigerator and freezer compartments, ensuring uniform temperature and efficient cooling. It helps maintain the desired temperature by moving air across the evaporator coils and distributing it evenly.

Causes of a bad evaporator fan motor can include electrical failures, worn-out bearings, or damage due to ice buildup. Regular wear and tear from continuous operation can also lead to motor failure over time.

Symptoms of a bad Evaporator Fan Motor include:

• The refrigerator or freezer not cooling properly
• Unusual noises coming from the fan area
• Frost buildup in the freezer compartment
• The fan not running when the refrigerator is on

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control module replaces the washer/dryer console's main control and restores cycle selection and electronic features. It manages appliance functions so settings respond correctly and cycles run as commanded. What it does:

• Controls cycle selection, timing and electronic user interface commands
• Interprets sensor inputs to start, advance or end cycles
• Restores normal electronic operation when failed module causes non-responsive controls
• Common symptom: appliance won't start, won't accept settings, or cycles stop unexpectedly

• One electronic control module

• Disconnect power (unplug or shut off breaker) before starting work
• Avoid static discharge; handle the board by its edges and wear anti-static protection if available
• Verify replacement part number matches the original module before installing

Replacement light lens cover for your refrigerator. Replace when cracked, discolored, or broken to restore proper lighting. Verify fit with your model number.