Samsung Switch

I replaced the energy regulator. Read more

• Element will not heat

1. Went online where I watched video about heat control for this Maytag. I then found AppliancePartsPros using Google. I ordered the part and In three days the part arrived. I installed the part and now the problem has been corrected. Read more

After removing the top rear access panel, I took as-built photographs of the two components to be replaced showing all wires, connectors and screws! The Energy Regulator for the front left burner was replaced first, noting the orientation before pulling off the knob, and removing the retaining screws. I used long nose pliers to gently remove one lead at a time and reconnect to the new regulator. Checked orientation against the photo, reinstalled regulator and knob. Main PCB Assembly was... Read more

• Won't start

I am so blessed. I went online. Found the brackets. Watch the video for the brackets I chose. And lucky me. I did not have to pull the dishwasher out. The installer did not have it flush under the counter. So I was able to pull the dishwasher forward unhook the damage brackets and insert the new. Put the dishwasher back in. Two screws. Now the balanced and secure dishwasher washes better than ever and I did not have to pay an extraordinary fee for a repairman. I'm 68 and take care of a 72 year... Read more

Simple remove and replace. Read more

We sent an email to AppliancePartsPros.com asking for their help in fixing our range. We gave them the model number (NE58F9500SS) of our Samsung Electric Range and told them about the faulty/dangerous two dual burners. We hated to get close to the range because the burners would turn on if you barely brushed by the range or if you would reach across it and accidentally touch the burner knobs all of a sudden you would feel heat or just see the light indicating the burner was on. We were... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

• Light not working

First, I modified old butter knife by bending a 90° angle about 3/4" from the tip. I slid the bent in up under the bottom of the switch cover and worked it to one side. I then rotated the knife downward using the bent end to pry the cover off. The switch is held by plastic arms on each side. The bottom right arm has a locating pin that fits into the switch. Unplugged the switch and re-installed. Read more

I used your chat and found out the year my stove was made. He also told me what part to order as one of the burners had stopped heating up. We watched the video on how to install it. My friend installed it and my stove burner now works. Read more

• Will not stop filling with water

This error code indicated faulty water level and wash cycles were exhibiting either no water or too much water. Saw utube vid using this part for this type of problem and so far the repair is working well. Part arrived in 2 days, it was the right part and the machine is working the way its supposed to so I'm very happy. The worst scenario would have been to hire a repair guy to rip me off for a "Johnson Rod" I didn't need. Read more

I replaced the control board and the microswitch. Read more

• Will not stop filling with water

Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more

Replaced the reed switch Read more

• Ice maker not making ice
• Not dispensing water
• Light not working

Ordered the Door Switch. Arrived the next day. It took less than 5 minutes to install the new switch. The beeping stopped immediately, light worked and temperature gauge showed 34 degrees. Read more