Parts for Ge GSE22KETEFBB: 08 - Sealed System & Mother Board Parts

Secures the drain tube to prevent water pooling or dripping. Replace if the clip is cracked, broken, or the tube has come loose. Verify fit with your model.

Fastener board bumper for side-by-side refrigerators. Secures and cushions mounting boards. Replace if cracked, broken, or missing for proper support.

Replacement rear wheel for refrigerators. Mounts to the bottom rear frame to enable smooth rolling for cleaning and repositioning. Order if cracked or missing.

Replaces a cracked, severed, or frozen ice maker fill tube and grommet. Delivers water from valve to ice maker. Includes tube, grommet, and plate.

Replaces a cracked, severed, or frozen ice maker fill tube and grommet. Delivers water from valve to ice maker. Includes tube, grommet, and plate.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This access cover protects internal components and wiring behind the appliance cabinet, keeping parts secure and helping maintain proper airflow. It replaces a cracked, missing, or damaged cover to restore safe, finished appearance. What it does

• Covers and protects control boards, wiring, or service areas inside the cabinet
• Prevents debris entry and reduces risk of accidental contact with electrical components
• Stops rattling or vibration caused by a loose or broken cover
• Helps restore the appliance's finished look after damage or repair

• One access cover

• Disconnect power before starting any work to avoid shock hazard
• Typically secured with screws or clips; retain hardware for reinstallation or replace if damaged
• Handle gently to avoid cracking; align tabs and fasteners before tightening

Rubber grommet that mounts the evaporator or condenser fan motor to its bracket. Replace when worn, cracked, or missing to reduce vibration and noise.

Guides airflow across the condenser and secures the fan motor in place. Replace if cracked, broken, or missing to restore proper cooling airflow.

Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.

Sealer plug for refrigerators. Seals unused holes or openings in cabinet panels. Replace if cracked, broken, or missing to maintain proper appearance.

Black snap-on plug button covers exposed holes or fasteners on refrigerator panels and trim. Replace missing, cracked, or damaged buttons to restore appearance.

Fix a refrigerator that's not cooling or has an overheated compressor. This condenser fan motor circulates air over the compressor and coils. DIY-friendly.

Refrigerator running hot or making loud noises? A worn condenser fan blade prevents proper airflow across coils. DIY repair in 30 minutes or less.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Hex washer head screw secures panels, brackets, and small assemblies inside refrigerators and ranges. Replace stripped, missing, or damaged screws.

This replacement machine screw fastens small appliance components and trim, restoring secure fit and preventing rattles or loose panels. Ideal for reattaching brackets, panels, and internal assemblies that use 8-32 fasteners. What it does:

• Secures panels, brackets, and internal components that use an 8-32 thread.
• Stops vibration and rattling caused by missing or loose screws.
• Restores proper alignment for removable trim or access panels.
• Matches the common hex washer-head style for a wide range of appliance mounting points.

• Use the correct 8-32 driver or hex socket to avoid stripping the head.
• Tighten firmly but do not overtighten; overtightening can strip threads or crack plastic.
• Disconnect power and remove any panels as needed before working on electrical components.
• If replacing multiple fasteners, replace all matching screws for even fit and alignment.

Rear condenser fan mounting bracket for refrigerators and freezers. Replaces broken, cracked, or missing brackets that secure the fan assembly.

Refrigerator not cooling or running constantly? This compressor replacement kit restores proper cooling. Professional installation strongly recommended.

Refrigerator not cooling or running constantly? A damaged condenser coil prevents proper heat release. This assembly restores cooling efficiency.

Fix a refrigerator that won't cool or runs constantly with this compressor start relay. Simple replacement takes 15-30 minutes with basic hand tools.

Fix a refrigerator that won't cool or runs constantly with this compressor overload protector. Protects against overheating. Simple plug-in installation.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement shelf support stud for refrigerator shelves. Installs to hold shelves in place. Needed when original stud is broken, cracked, or missing.

Condenser air baffle for refrigerators. Directs airflow over the condenser coils. Replace if cracked, broken, or missing to maintain proper air circulation.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

10-32 x 5/16 machine-thread screw secures refrigerator panels, trim, and internal brackets. Replaces missing or damaged fasteners to prevent rattles.

This self-adhesive foam strip provides a flexible seal and buffer for appliance gaps, helping reduce drafts, rattling, and moisture intrusion. Designed for easy stick-on replacement where foam padding or sealing is needed. What it does

• Seals small gaps between components to help reduce air leaks and temperature loss
• Cushions panels and doors to minimize noise and vibration
• Helps block moisture and dust from entering sensitive areas
• Self-adhesive backing allows for quick placement without extra glue

• One self-adhesive foam strip

• Surface must be clean and dry; wipe with isopropyl alcohol for best adhesion
• Measure and trim the foam strip to fit—use scissors or a utility knife
• Press firmly along the length to ensure full contact; allow adhesive to set before closing doors or panels
• For safety, disconnect power to the appliance before working in internal areas

Secures the condenser unit in your refrigerator. Replace if loose, broken, or causing vibration noise. Verify fit with your model number before ordering.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

No water or ice? This inlet valve assembly controls water flow to your refrigerator's dispenser and ice maker, restoring fill function in under an hour.

Fix a refrigerator that won't cool or runs constantly with a new main control board. This central controller manages compressor and defrost cycles.

Strain relief retainer secures electrical cables where they enter the refrigerator. Replace if cracked, broken, or missing to protect wiring connections.

Plastic water line that runs from the water valve to the icemaker fill tube. Replace if cracked, brittle, broken, or leaking at connection points.

Molded splash shield that directs water away from internal components. Replace if cracked, broken, or missing to restore proper water routing protection.