Parts for Lg WM2233HW / ABWEEUS: Section 3 Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Wire harness for washer control systems. Connects electronic components and delivers power throughout the machine. Replace if wires are frayed or damaged.

This three coil solenoid is used for the cold water, bleach dispenser and prewash.

Fix washer IE error or no water flow issues with this water inlet valve. Controls hot or cold water flow into wash drum. 15-minute DIY repair.

Fix a loose or missing fabric softener cap that won't stay in place or causes drawer issues. Simple snap-in replacement restores proper dispensing.

Bleach dispenser funnel for LG front load washers. Installs in detergent drawer to safely dispense bleach. Replace if cracked, broken, or missing.

Fix detergent not dispensing or a broken dispenser drawer. This washer detergent box assembly holds and releases soap properly. DIY-friendly repair.

This inlet hose supplies fresh water from the household line to the dishwasher. Replace a damaged or leaking hose to help restore proper filling and prevent water leaks during operation.

• Channels water from the supply valve to the dishwasher's inlet
• Common failure signs: leaks under or behind the unit, fill errors, slow or no fill
• Helps resolve intermittent water supply issues caused by a kinked or cracked hose

• Unplug power and shut off the water supply before starting
• Place a towel or pan to catch residual water when disconnecting
• Check for leaks after installation and tighten connections as needed

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This inlet hose is the internal water line for your dishwasher, routing fresh water from the fill valve into the wash system. Replacing a brittle or leaking hose restores reliable filling and helps protect floors and cabinetry from water damage.

• Channels incoming water from the inlet valve to the tub/sump
• Maintains proper fill level and flow at the start of each cycle
• A cracked, kinked, or loose hose can cause leaks or slow/no fill
• Restores correct water delivery and helps prevent water damage

• Disconnect power and shut off the water supply before servicing
• Pull the dishwasher forward for access; place a towel or pan to catch residual water
• Note the original routing and clamp positions; transfer clamps and avoid kinks
• Restore water, run a quick fill cycle, and check all connections for leaks

Fix detergent not dispensing or leaking from drawer. This dispenser assembly includes compartments for detergent, bleach, and softener. 15-minute DIY repair.

Directs water from inlet valve to detergent dispenser in LG washers. Replace if hose is cracked, leaking, won't stay attached, or damaged from wear.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

Flexible drain hose assembly that carries wastewater from your washer to the household drain. Replace if cracked, leaking, or damaged during installation.

Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.