Parts for Lg LFD22860TT / ATICLGY: Section 4 Parts

Mounting screw for refrigerator internal components and panels. Replaces lost, stripped, or damaged screws during repairs or part installations.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

The Door Gasket is an OEM part for LG refrigerators. This gasket seals the refrigerator door, ensuring a tight closure to maintain the internal temperature and prevent cold air from escaping. By creating an airtight seal, the door gasket helps keep food fresh and reduces energy consumption.

You should replace the door gasket if it becomes worn or damaged. Causes of a bad door gasket can include wear and tear over time, damage from repeated opening and closing of the door, or warping due to temperature fluctuations.

Symptoms of a bad door gasket include:

• Warm spots inside the refrigerator
• Excessive condensation or frost buildup
• The refrigerator door not closing properly
• Increased energy bills

This OEM LG part is also compatible with Sears/Kenmore models.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This genuine door gasket assembly creates a tight seal around the appliance door to prevent air and moisture loss, helping the appliance maintain temperature and operate efficiently. What it does:

• Seals the door opening to stop air leaks and reduce energy loss
• Helps prevent condensation, spills, and drafts from escaping the cabinet
• Restores proper door closure and improves temperature consistency
• Commonly replaced when the existing gasket is torn, warped, or no longer seals

What's included: One door gasket assembly as shown Install notes:

• Disconnect power (and water, if applicable) before starting any repair
• Remove the door or access trim to access the gasket mounting channel
• Inspect the door flange and gasket seating surface; clean debris before installing the new gasket
• Use only manufacturer-recommended fasteners and replace any damaged retainers; test door operation and seal after installation

The Holder Gasket is an OEM part for LG refrigerators. This gasket creates a tight seal between the holder and the refrigerator's interior, preventing air leaks and maintaining optimal cooling efficiency.

Common causes of a bad gasket include wear and tear over time, exposure to extreme temperatures, or accidental damage during maintenance or cleaning.

Symptoms of a bad gasket include:

• Air leaks leading to temperature fluctuations
• Increased energy consumption
• Frost or condensation buildup inside the refrigerator
•  Difficulty maintaining consistent temperatures

This OEM LG part is also compatible with Sears/Kenmore models.

The Gasket Holder is an OEM replacement part for LG refrigerators. It is a mount located around refrigerator doors that secures the gaskets in their tracks. About 37.5" long

Potential failure causes relate to consistent flexing and impact stresses warping holder material over many years. Mineral buildup inhibiting a flush seal is also possible.

Symptoms involve:

• Cold air infiltration from gaps where gaskets no longer fit tightly
• Condensation or frost accumulated on external door panels
• Ice buildup inside due to insufficient insulation performance
• Gaskets detaching from holder tracks rendering them useless

This OEM LG part is also compatible with some Sears/Kenmore models.

The Gasket Holder is an OEM replacement part for LG refrigerators. It is a mount located around refrigerator doors that secures the gaskets in their tracks. About 37.5" long

Potential failure causes relate to consistent flexing and impact stresses warping holder material over many years. Mineral buildup inhibiting a flush seal is also possible.

Symptoms involve:

• Cold air infiltration from gaps where gaskets no longer fit tightly
• Condensation or frost accumulated on external door panels
• Ice buildup inside due to insufficient insulation performance
• Gaskets detaching from holder tracks rendering them useless

This OEM LG part is also compatible with some Sears/Kenmore models.

The Gasket Holder is an OEM part for LG refrigerators. This part holds the door gasket in place, ensuring a tight seal around the refrigerator or freezer door. 

Over time, the gasket holder can become warped or damaged due to frequent use, temperature fluctuations, or accidental impacts. 

Symptoms of a bad Gasket Holder include:

• Loose or sagging door gasket
• Noticeable gaps between the gasket and the door frame
• Difficulty in maintaining consistent refrigerator temperatures
• Increased condensation or frost inside the appliance

This OEM LG part is also compatible with some Kenmore models.

The Gasket Holder is an OEM replacement part for LG refrigerators. It is inside the freezer door and functions to securely seal in cold air. The holder provides a mounting point and compression fit for the door gasket, preventing air leakage along the perimeter.  

Symptoms of a bad gasket holder include:

• Cold air escaping around the door seal 
• Frost or moisture buildup near the gasket area
• The door not shutting tightly 

Note: About 38.5" long

Over time, the holder's mounting points can warp or weaken from repeated opening and closing of the freezer door. This allows for gasket movement and compromised sealing.

This replacement is compatible with Sears/Kenmore models as well.

Replaces the left door closing cam on bottom-mount refrigerators. Installs inside the door to help ensure proper closing and sealing when broken or worn.

Replaces broken or worn door closing cam on bottom-mount refrigerators. Installs at lower hinge to control smooth door movement. Needed when cam cracks or breaks.

Replace your refrigerator's guide sleeve if cracked, broken, or missing. This component helps direct and protect moving parts during operation.

Replace your cracked, broken, or missing refrigerator door bin. Provides convenient storage for condiments, beverages, and snacks on the door.

Plastic door stop that limits refrigerator door swing range. Replaces broken, cracked, or missing stoppers causing doors to swing too wide or close improperly.

Slide rail for bottom-mount refrigerator freezer drawer. Replaces broken, binding, or worn rails that prevent drawer from opening or closing smoothly.

Slide rail for bottom-mount refrigerator freezer drawers. Replaces broken, cracked, or binding rails causing uneven drawer movement or closure issues.

Secures and transmits motion between drawer drive and slide assembly. Replace if broken, cracked, or missing to restore smooth drawer operation and alignment.

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

Replacement door hinge assembly for refrigerators. Supports and pivots the door for smooth operation. Replace if bent, worn, or broken to restore alignment.

Replacement door hinge bushing for refrigerators. Installs in door hinge mechanism. Replace when worn, cracked, or causing door grinding or misalignment.