Parts for Whirlpool WRF736SDAM10: 06 - Shelf Parts

Replaces a cracked, broken, or missing front panel on your refrigerator's full-width pantry drawer. Restores the handle and clean appearance for smooth operation.

Replacement drum support roller that helps the dryer drum rotate smoothly and quietly. Installs where the drum rests to reduce noise and uneven rotation caused by worn or damaged rollers. What it does:

• Supports and guides the tumble/drum as it spins to maintain proper alignment.
• Reduces squeaks, rumbling, and scraping noises from worn or seized rollers.
• Prevents excessive belt wear and uneven drum movement that can lead to vibration.
• Restores smoother rotation when original rollers are cracked, worn, or binding.

• Disconnect power (and gas, if applicable) before beginning any repair.
• Access the roller by removing the dryer access panel or drum per your model's service instructions; support the drum to prevent it from falling.
• Inspect adjacent parts (idler, rollers, shaft, and belt) and replace if worn to avoid repeated failures.

Structural support bracket for bottom-mount refrigerators. Installs internally to secure components. Replace if cracked, broken, or missing.

Plastic ladder support that holds door shelves in place on your refrigerator. Replace if cracked, broken, or missing to restore proper shelf mounting.

Replace your refrigerator's cracked, broken, or worn glass shelf. This clear storage shelf installs inside the fresh food compartment to organize food.

This sachet holder housing assembly secures single-use detergent or cleaning sachets inside the dispenser so they stay in place and release correctly during cycles. Replacing a cracked or broken holder restores reliable sachet positioning and dispensing. What it does:

• Holds detergent/cleaning sachets in the dispenser so they don't shift or drop into the tub.
• Ensures sachets stay aligned for proper release during the wash or cleaning cycle.
• Helps prevent sachets from rupturing or blocking the dispenser area.
• Common symptoms of a bad holder: sachets falling out, sachets not dispensing properly, or poor wash/cleaning results.

• Disconnect power (and water, if required) before servicing the dispenser area.
• Access the dispenser per the owner's manual; the holder typically snaps into place or secures with a small fastener.
• Handle plastic clips and tabs gently to avoid breakage; use a non-marring pry tool if needed.

Replace your broken or cracked refrigerator crisper pan. This drawer pan stores fresh produce in the lower compartment. Sold without axle and rollers.

Replacement glass shelf for your refrigerator. Installs inside the fresh food compartment. Needed when original shelf is cracked, broken, or missing.

Plastic front panel that attaches to your refrigerator's crisper drawer. Replace if cracked, broken, or detached. Snaps into place on the drawer frame.

The Storage Drawer is an OEM replacement part for Whirlpool refrigerators. It provides customizable organization for items like snack foods, beverages, and condiments inside the refrigerator cabinet. The drawer measures approximately 27"x 20"x 6".

Causes of a bad storage drawer can include broken mounting slides, making it difficult to open or close securely. Overpacking may also cause cracks in the plastic construction over time.

Symptoms of a bad storage drawer include:

• Will not stay fully closed when loaded
• Mounting brackets crack or break off from vibration
• Contents spill out easily due to loose fit

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replace a cracked, broken, or missing half-width stationary shelf in your refrigerator. Restores storage space and keeps food organized securely.

Control knob for refrigerators. Mounts on the control panel to adjust temperature settings. Replace if cracked, broken, or missing for proper control.

Tempered glass shelf for refrigerator crisper drawer compartment. Replaces cracked, chipped, or missing original shelf. Provides stable storage surface.

Plastic frame that supports the glass shelf above refrigerator crisper bins and forms drawer slide tracks. Replace if cracked, broken, or missing.

Secures and aligns the rear of your refrigerator crisper drawer for stable, smooth sliding. Replace if broken, cracked, or worn to restore proper fit.

Replace your broken or cracked refrigerator crisper pan. This drawer pan stores fresh produce in the lower compartment. Sold without axle and rollers.

This replacement plate is a small mounting component that secures or supports nearby parts and helps maintain proper alignment and clearance inside the appliance. It restores stable fit and prevents rubbing or movement of adjacent components. What it does

• Provides a firm mounting surface to secure fasteners or assemblies
• Keeps parts aligned to reduce wear and noise
• Helps maintain proper spacing and clearance for moving parts
• Addresses symptoms like loose trim, rattling, or misaligned components

• One replacement plate as shown

• Recommended for technicians or experienced DIYers; verify orientation before removing original
• Disconnect power to the appliance before starting work to avoid shock or injury
• Keep all fasteners and clips; reuse original hardware unless replacements are provided
• Tighten screws to snug only—avoid overtightening which can warp the plate or strip threads

Mounting plate for bottom-mount refrigerators. Secures internal components in place. Replace if cracked, broken, or missing to restore proper support.

Drawer slide rail for bottom-mount refrigerators. Mounts to the drawer frame to allow smooth gliding motion. Replace if cracked, broken, or worn.

Drawer slide rail for refrigerator storage compartments. Replaces broken, cracked, or worn slides that prevent smooth drawer operation or cause misalignment.

This is a factory replacement plate used as a structural mounting/support piece within the appliance. Replacing a damaged or missing plate restores a secure, correctly aligned connection between parts and helps eliminate looseness or vibration.

• Provides a rigid surface to mount or support related components
• Maintains alignment and spacing within the assembly
• Helps prevent rattling, looseness, or shifting when secured properly
• Replace if bent, cracked, corroded, threads stripped, or missing

• Disconnect power (and shut off gas/water if applicable) before service
• Note hardware locations and orientation; take photos during disassembly
• Transfer any clips or fasteners from the original plate if reused
• Align and level the plate, then tighten fasteners to manufacturer guidance

Structural support plate that reinforces the crisper drawer assembly in your refrigerator. Replace if broken, cracked, or missing to restore drawer stability.

Molded trim piece that covers the top of your refrigerator's pantry or produce drawer area. Replace if cracked, warped, or missing to restore a clean look.

Replacement internal support bracket for refrigerators. Secures and stabilizes components for proper alignment. Replaces worn, broken, or missing supports.

Control panel cover broken or missing? This protective cover restores your refrigerator's finished look and shields electronics from dust and spills.

Replacement screw for securing refrigerator panels, brackets, and components. Needed when original fasteners are missing, stripped, or damaged.

Front support bracket that secures your refrigerator's crisper drawer for smooth sliding and proper alignment. Replace if cracked, broken, or missing.

Mounting screw secures panels, trim, and internal components to your refrigerator frame. Replace when original is missing, stripped, or damaged.

This outer door trim is a factory-style replacement that restores the oven or range's finished appearance and helps seal the control-panel/door gap. It replaces a cracked, bent, or missing trim piece for a clean, factory look. What it does:

• Covers the outer edge of the oven/control opening to improve appearance and finish
• Helps maintain a consistent fit between the door and surrounding cabinet/console
• Prevents debris buildup in the seam and reduces visible gaps or drafts
• Restores proper mounting points if original trim is damaged or warped

• One outer trim piece as pictured

• Turn off and disconnect power (and gas if applicable) before beginning repairs
• Handle trim carefully to avoid scratching the finish; use manufacturer instructions for door/panel removal if required
• Use existing fasteners unless replacements are specified by the manufacturer

Replacement plastic crisper pan that sits under the drawer to support produce and catch spills. Replace if cracked, broken, or missing to keep interior clean.

This Whirlpool Front Pan is an OEM part for select Whirlpool refrigerator models. Specifically designed for the interior storage section of the refrigerator, this front pan provides a durable and convenient space for organizing and storing food items.

The front pan in a refrigerator can experience wear or damage over time due to regular use, heavy storage items, or accidental impacts. Common issues include cracking, warping, or breaking, which can reduce the usability of the refrigerator's storage space and affect its overall aesthetic.

Symptoms of a damaged fridge front pan include:

• Visible cracks or breaks in the pan.
• Difficulty in sliding the pan in and out or fitting it securely.
• Sagging or warping, especially under the weight of stored items.
• The pan becomes loose or dislodges easily.
• Reduced effectiveness in organizing and storing food items.

This genuine Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, and Kenmore models.
 

Replacement housing assembly for refrigerators. Secures internal components and restores structural support. Replaces cracked, broken, or missing housings.

Track guide that mounts to the refrigerator shelf frame for the crisper drawer roller. Replace if cracked, broken, or worn to restore smooth drawer glide.

Secures the roller to your refrigerator drawer so crisper and pantry pans glide smoothly. Replace when drawers stick or wobble. Confirm fit by model number.