Parts for Electrolux CPEF3077QFB: 04 - Top / Drawer Parts

This interior refrigerator liner replaces a damaged or worn cabinet surface to restore a clean, smooth interior and support shelves and drawers. It helps maintain a sanitary storage area and a proper fit for accessories. What it does:

• Provides a smooth, easy-to-clean interior surface for the fresh food compartment
• Restores mounting surfaces for shelves, bins and trim pieces
• Prevents drafts and moisture intrusion where cracks or gaps exist
• Addresses symptoms like visible cracks, gouges, or a warped/loose interior liner

• One refrigerator interior liner

• Disconnect power to the appliance before beginning any repair
• Removal typically requires taking out shelves, trim and fasteners to access the liner
• May require adhesive, clips or screws specific to the model—keep original fasteners and hardware

Outer panel for your range warming or storage drawer. Replaces cracked, dented, or discolored drawer front. Restores appearance and structure.

Rear glide attaches to the back of your range storage drawer, allowing smooth sliding motion. Replace if broken, cracked, or missing to prevent drawer tilt.

Drawer slide glide for electric and gas ranges. Replace if cracked, broken, or worn to restore smooth, aligned drawer movement and eliminate sticking.

Secures components and panels on your range. Replace this nut if it's stripped, corroded, missing, or no longer holding parts firmly in place.

This 100W radiant element replaces a failed warming element to restore gentle, even heat in the appliance's warmer/drawer. It delivers low-profile radiant heat for keeping food warm between cooking and serving. What it does:

• Radiates low-level heat to maintain food temperature in the warmer or drawer
• Replaces a broken or non-heating warmer element
• Common symptom: warmer drawer not holding temperature or not heating
• Works as the heating element that sits under the warming surface to provide consistent warmth

• Disconnect power to the appliance before attempting service
• Inspect mounting and wiring; replace any damaged connectors or mounting hardware as needed
• Handle the element carefully to avoid bending or damaging the heating surface

Cooktop burner not heating? This radiant element restores heat to non-working zones on glass-top ranges. Moderate DIY repair with oven access required.

Burner won't heat evenly or only outer ring works? This dual 9/12 inch radiant surface element restores proper heating. Easy DIY replacement in minutes.

Burner not heating? This 6-inch surface heating element restores cooktop function. DIY repair in 10-30 minutes with basic tools and simple instructions.

Replace your range's main top panel if cracked, damaged, or worn. This cooktop surface covers the burner assembly and provides a clean cooking area.

Secures and aligns your range oven door hinge for smooth operation. Replace this bracket if cracked, broken, or causing door misalignment issues.

Mounting bracket for electric and gas ranges. Secures components in place. Replace if bent, cracked, or broken to restore proper fitment and stability.

Secures internal components and panels in your range. Replace this mounting bracket if cracked, broken, or missing to restore proper support and alignment.

Replace the channel trim on your range door when it becomes cracked, broken, or damaged. This structural component installs along the door edge for a secure fit.

This door handle replaces a worn, damaged, or missing refrigerator door handle to restore a solid grip and normal door access. It installs on the exterior of the fridge door and gives a finished look while providing reliable pulling strength. What it does:

• Provides a secure grip for opening and closing the refrigerator door
• Replaces cracked, broken, loose, or missing door handles
• Restores proper handle alignment and ergonomics to reduce strain when opening
• Helps maintain the appliance's appearance by covering damaged areas

• Disconnect power or unplug the appliance and empty the door area before starting
• Removal usually requires loosening or removing a few screws or clips from the interior door panel
• Preserve and reuse existing mounting screws or brackets unless new hardware is explicitly listed as included
• Do not overtighten fasteners; test operation after installation to ensure proper alignment and seal

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Touch-up paint for electric ranges. Covers scratches, chips, and worn spots on exterior surfaces. Essential for restoring appearance after damage.

Black mounting screw that secures range body side panels. Replace if stripped, missing, or corroded. 8-18 x 11/16 inch fastener for structural assembly.

Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.

Size: 6-20 x 0.312 inch.

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.