Parts for Electrolux EW30GS65GS3: 09 - Top / Drawer Parts

Replace your range's damaged, cracked, or faded control panel. Restores the front console interface where buttons and displays mount. Direct fit replacement.

Decorative trim piece for range oven door. Replaces cracked, chipped, or missing trim. Installs along door edge to restore finished appearance.

Gas burners won't ignite? A faulty spark module may be the issue. This part sends electrical current to igniters. DIY-friendly, takes minutes.

Replace your range's control panel frame trim if it's cracked, broken, or damaged. This trim piece surrounds the control panel for a finished look.

Low-friction glide that supports and guides range drawer movement. Replace if cracked, broken, or worn to restore smooth sliding without sticking or scraping.

Low-friction slide piece that supports moving components in your range or wall oven. Replace worn or cracked glides to restore smooth operation.

Metal main top assembly for ranges. Replaces cracked, dented, or worn cooktop surface. Installs as the outer shell covering burner components.

Replacement burner grate for gas ranges. Sits on top of the cooktop to support pots and pans. Replace if cracked, broken, or worn from heat exposure.

Cast iron grate that sits on top of your range burner. Replace if cracked, broken, or chipped from drops or wear. Ensures stable pot and pan support.

Replace your damaged or deformed range cooktop grate to restore stable support for pots and pans. Essential when your grate is cracked, warped, or broken.

Removable griddle plate that sits over range burners to create a flat cooking surface. Replace yours if cracked, warped, or worn for even cooking.

Replace your worn, cracked, or missing cooktop control knob. Attaches to the control shaft for secure fit and clear heat setting selection.

Replacement control knob for your range. Attaches to the control shaft to operate burners or oven functions. Replace if cracked, broken, or missing.

Replacement spacer for ovens and ranges. Maintains proper spacing between components. Replace if cracked, broken, or missing to restore alignment.

Oven trim piece that frames the control panel or door edge. Replace if cracked, chipped, discolored, or missing to restore a finished appearance.

Insulation panel for gas ranges. Installs inside the range cavity to provide sound dampening and thermal protection. Replace if torn, damaged, or missing.

Oven not heating or baking unevenly? This lower bake element restores proper heating for even cooking. Moderately easy DIY repair in 30-45 minutes.

Oven not heating to set temperature or heating too slowly? This thermostat controls oven temperature cycling. Test for continuity to diagnose the issue.

Replacement wire shelf that supports cookware inside the oven cavity. Install when your original rack is bent, rusted, warped, or missing.

Replace your range's control panel if the original is cracked, damaged, or showing wear. This panel mounts to the front and houses control components.

Range drawer glide with integrated ball bearings ensures smooth drawer operation. Replace when drawer sticks, won't close, or bearings are bent or damaged.

This wiring harness is the factory-style electrical assembly that connects appliance controls and components for reliable power and signal routing. Replacing a damaged harness restores proper electrical connections and helps resolve intermittent or failed operation. What it does:

• Routes power and control signals between the control module and components
• Restores reliable electrical connections when wires or connectors are damaged
• Helps correct symptoms such as intermittent power, failed cycles, or non-responsive controls
• Prevents shorts and arcing caused by exposed or frayed wiring when correctly installed

• Disconnect power (unplug appliance or switch off breaker) before servicing to avoid shock or injury
• Inspect connectors and mounting points; secure harness away from heat and moving parts
• Use proper strain relief and routing to prevent chafing or contact with sharp edges

Replacement mounting screw for refrigerators, ovens, ranges, and cooktops. Secures interior panels, components, and trim. Needed when original is stripped, missing, or damaged during repair.

Rubber bumper that cushions your range door, reducing noise and preventing wear. Replace if cracked, missing, or worn to restore proper door contact.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Specs: 8 - 18 x 0.500

This door gasket seals the refrigerator door to help maintain proper temperature and energy efficiency by preventing warm air from entering the cabinet. It replaces a worn or torn seal to restore a tight closing perimeter. What it does:

• Creates an airtight seal around the refrigerator door to help keep cold air in and warm air out.
• Helps reduce frost buildup and keeps food at consistent temperatures.
• Commonly replaces gaskets that are cracked, flattened, torn, or no longer form a tight seal.
• Can reduce excessive compressor run time and cycling caused by air leaks.

• One refrigerator door gasket.

• High-level DIY replacement: remove the old gasket, clean the door flange, and press the new gasket into the retainer channel; some gaskets may require slight heating to set the fit.
• Check alignment and ensure gasket fully seats around the door perimeter before testing.
• Use basic hand tools; disconnect power if working near electrical components or lighting.

Secures the oven door handle in place. Replace if screw is stripped, missing, or no longer holding the handle firmly against the door surface.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head