Parts for Kenmore 790.75904993 (79075904993, 790 75904993): Top & Drawer Parts

Replacement owner's manual for your range. Provides operating instructions, maintenance guidelines, and safety information if original was lost or damaged.

Size: 8-18ab x 0.5 inch.

Low-friction glide that supports and guides range drawer movement. Replace if cracked, broken, or worn to restore smooth sliding without sticking or scraping.

Size: 10 fl. oz. Used on glass, ceramic and porcelain cooktops.

This is a 100 watt, 120 volt surface warming element. Includes limiter.

Black burner drip pan that sits beneath cooktop burner elements to catch spills and drips. Replace if cracked, discolored, warped, or missing.

Replacement drip pan for your range. Sits beneath the burner element to catch spills and debris. Replace if cracked, warped, rusted, or discolored.

This trim ring is a decorative finish piece that restores the appliance's factory appearance and covers the gap between panels. It provides a clean, finished look and protects the underlying edge from chips and grime. What it does:

• Covers and protects the exposed edge of the appliance panel or opening
• Restores factory appearance after damage or during repairs
• Prevents dirt and debris from collecting in the panel seam
• Common symptom: cracked, chipped, loose, or missing trim that affects appearance

• One trim ring

• Disconnect power to the appliance before starting any repair
• Typically installs with clips or screws; handle carefully to avoid scratching the finish
• Verify exact fit by matching the part number to your appliance before installing
• If trim is attached to other components, remove surrounding parts in the order recommended by the service manual

Replaces cracked or discolored drip pan trim ring on your range. Installs around the burner bowl to provide a finished look and protect the cooktop.

Trim ring that fits around cooktop drip pans for a finished appearance. Replace if cracked, discolored, warped, or missing for a clean look.

This burner cap sits on top of a surface burner head to help shape the flame and protect the burner assembly. It restores proper flame pattern and helps ensure even cooking on gas cooktops. What it does:

• Centers and shields the burner head for consistent flame distribution
• Helps produce an even flame for reliable heating across cookware
• Prevents food and spills from reaching the burner ports
• Commonly replaced when warped, corroded, or causing uneven or erratic flames

• One burner cap

• Turn off the gas supply and allow the cooktop to cool completely before servicing
• Lift off the old cap, clean the burner head, and set the new cap in place so it sits flat and centered
• Do not force the cap; if it does not seat properly, check for debris or damage to the burner head
• If you smell gas or see an abnormal flame after installation, stop use.

Replace your cooktop's large burner cap if the original is cracked, chipped, discolored, or missing. Sits on top of the burner head for proper flame.

This door gasket seals the refrigerator door to help keep cold air in and warm, humid air out—reducing frost build-up and helping the appliance run more efficiently. Fits where a full perimeter door seal is required. What it does:

• Creates an airtight seal around the refrigerator door to maintain consistent internal temperatures.
• Helps prevent warm air infiltration, moisture, and frost accumulation inside the compartment.
• Reduces energy waste caused by a failing or damaged door seal.
• Common symptoms of a bad seal: condensation at the door, frost on shelves, fluctuating temperatures, or higher energy use.

• Disconnect power to the appliance before attempting any service.
• Remove the old gasket carefully; replacement typically seats into the door channel around the full perimeter.
• Inspect and, if needed, adjust door alignment and hinge condition to ensure a proper seal.

Size: 10-32 x 0.312 inch. Color: Black.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Mounting bracket that secures the heating element in your range. Replace this bracket if it's bent, broken, cracked, or missing to properly support the element.

Replacement wire shelf that supports cookware inside the oven cavity. Install when your original rack is bent, rusted, warped, or missing.

Guide pin for gas ranges. Secures and aligns oven or burner components. Replace if broken, missing, or worn to restore proper part positioning.