Parts for Frigidaire 6589-80B: Cabinet / Top Panel / Base Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

The hinge grommet provides cushioning and smooth operation where the washer lid connects to the main body. Replace if the lid doesn't close properly, makes grinding noises when opening/closing, or appears loose and wobbly.

Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring proper water supply when the valve fails. Direct-fit replacement that helps stop leaks, no water flow, or intermittent dispensing. What it does:

• Opens and closes to allow water into the ice maker and/or door dispenser when requested
• Stops water flow when idle to prevent leaks and overfilling
• Common repair for no water, slow fill, or continuous dripping from dispenser or ice maker
• Electromechanical valve driven by refrigerator control signals

• Disconnect power and shut off the household water supply before starting
• Replace only with parts specified for your model;
• Inspect and tighten or replace inlet hoses and clamps if corroded or damaged

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This part has been discontinued by the manufacturer and is no longer available.

Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.

Shipping block for washers, installs inside cabinet to secure the tub during transport or moving. Replace if lost, broken, or missing from original packaging.

Fix detergent not dispensing properly with this washer detergent dispenser cup. Solves leaking or broken dispenser issues. Simple install in 15 minutes.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. Instructions included.

This washer switch is both the lid lock and lid switch. New mounting bracket replaces older design. Which means in some applications you may need to drill off old design mounting bracket prior to mounting the new lock. If your replacing the 4 wire switch you will need to tape off light switch leads. The light will no longer be used. Instructions included.

Fix a bleach dispenser that won't drain or empty during wash cycles. This washer bleach cup sits under the lid and uses gravity flow to dispense bleach.

Fix detergent not dispensing properly with this washer detergent dispenser cup. Solves leaking or broken dispenser issues. Simple install in 15 minutes.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.