Parts for Ge GFWR4805F2MC: Controls & Dispenser Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replace your washer's broken, cracked, or missing control knob with this rubberized grip selector dial. Installs on the control panel for secure turning.

This knob retainer secures a control knob to its switch/timer shaft, keeping your selections engaged and the knob firmly in place. Replace a worn or missing retainer to restore a solid feel and dependable operation.

• Holds the control knob securely on the switch/timer shaft
• Restores positive engagement when turning the knob
• Common fix for a loose, slipping, wobbly, or falling-off knob
• Helps resolve intermittent selection when the knob doesn't grip the shaft

• Disconnect power before servicing
• Pull off the knob to access the retainer
• Align the new retainer with the shaft and press firmly until fully seated
• Reinstall the dial/knob and verify proper engagement

This screw is a direct-fit fastener used to secure appliance panels and components for stable, rattle-free operation. Replacing a stripped, missing or worn screw restores proper part alignment and prevents vibration or loose trim. What it does:

• Secures panels, trim pieces or small components to the appliance frame
• Prevents rattling or movement caused by missing or loose hardware
• Restores proper alignment for switches, panels or covers
• Works as a replacement for a single lost or damaged mounting screw

• Disconnect power and water before beginning any repair
• Use the correct screwdriver bit to avoid stripping the head
• Start threads by hand, then tighten snugly — avoid over-tightening
• Keep removed hardware in a labeled container to avoid loss

Washer won't turn on or buttons unresponsive? This user interface control board assembly powers your washer's control functions. Moderate DIY repair.

10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.

Replace a cracked or leaking dispenser drawer body housing in your washer. This molded housing securely holds the dispenser assembly components.

Replacement siphon cap that seals the drain tube connection in your washer. Needed when the original cap is cracked, broken, or missing to prevent leaks.

If detergent isn't dispensing properly during wash cycles, this siphon cup channels detergent from the dispenser into the tub. Simple DIY fix.

If your washer's detergent drawer pulls out too far or won't stay in place, the dispenser drawer retainer may be broken. Simple snap-in fix.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replacement logo badge emblem for appliance exterior panels. Restores original appearance when emblem is missing, faded, cracked, or damaged. 1 piece.

This small closed grommet seals and cushions a screw hole to protect wiring and reduce vibration. It prevents chafing where a fastener passes through a sheet-metal panel, helping maintain safe wiring and a quieter appliance. What it does:

• Seals a screw or bolt hole to keep wires and harnesses from rubbing on sharp edges
• Cushions and isolates vibration to reduce noise and wear
• Helps maintain a tight fit where panels or components meet
• Commonly used where a harness or lead passes through a chassis opening

• One closed grommet

• Inspect panel edges and harness before installing; replace if damaged
• Push grommet into the hole until fully seated; route wiring through the grommet
• Disconnect power to the appliance before any access or repairs

Fix washer water flow issues with a new diverter drive assembly. Controls water distribution during wash cycles. Moderate DIY repair for most models.

Fill hose for washing machines. Connects the water supply to your washer drum. Replace if cracked, leaking, or damaged to restore proper water flow.

This O-ring is a small rubber sealing gasket designed to restore a watertight seal in the appliance where the original O-ring has worn, cracked, or gone missing. It prevents leaks and helps maintain proper water flow. What it does:

• Seals joints and hose connections to stop water leaks
• Restores proper sealing where a worn O-ring causes dripping
• Helps maintain consistent water pressure by preventing leaks
• Commonly replaced when removing or reinstalling water fittings or valves

• Inspect the mating surfaces for damage and clean thoroughly before installing
• Lubricate with food-safe silicone grease to ease installation and preserve the seal
• Ensure correct seating in the groove; do not stretch excessively when fitting
• Disconnect power and shut off the water supply before servicing water connections

This genuine replacement clamp secures flexible hoses to fittings to keep connections tight and help prevent leaks and disconnection. It restores a secure seal for appliance water or vent hose connections. What it does:

• Holds a rubber or plastic hose tightly onto a spud or nipple to prevent leaks and slips
• Helps stop water or air from escaping at hose connections
• Reduces vibration and hose movement that can wear connections over time
• Commonly used where a small, durable clamp is needed on supply, drain or vent hoses

• Disconnect power and turn off water supply before beginning work
• Remove the old clamp with pliers or a screwdriver, then position the new clamp evenly over the hose end
• Tighten or crimp per the clamp style until the hose is snug but not pinched
• Inspect the connection for leaks after restoring power/water

A small replacement clamp that secures hoses and prevents leaks or disconnections. Use this clamp to restore a tight, vibration-resistant connection where a hose or flexible line needs fastening. What it does

• Holds a washer, dryer, dishwasher or refrigerator hose or flexible line in place to prevent leaks and blow-offs
• Reduces vibration and movement that can cause wear or fraying of hoses
• Restores a loose or missing fastening point that can allow fluid or air escape
• Simple mechanical function—no electrical components

• One clamp

• Turn off and unplug the appliance and shut off water or supply lines before starting work
• Confirm hose orientation and seat hose fully before sliding the clamp into position
• Use the correct clamp tool or pliers to compress/secure the clamp without distorting it
• Replace any worn or damaged hoses or fittings when installing this clamp

If your washer dispenser leaks or has poor water flow, this dispenser body assembly channels water properly and restores dispensing control.

Fix detergent not dispensing or leaking from the dispenser with this washer inlet nozzle. Common repair for GE front-load washers. Simple installation.

This SCR 6-19 thyristor is a board-mounted power control component used on compatible appliance control boards to regulate current to heating and motor circuits. Replacing a faulty SCR restores proper power switching and stable operation. What it does:

• Controls/rectifies power to heating elements or motor circuits on the control board
• Allows timed or variable power delivery as directed by the appliance control electronics
• A failed SCR can cause no heat, intermittent heating, or loss of controlled motor/power functions
• Works as the switching element for the board's high-current paths

• One SCR 6-19 thyristor

• Disconnect power at the breaker or unplug the appliance before servicing
• Board-level replacement may require desoldering/soldering skills or a hot-air rework station
• Handle the part and PCB with ESD precautions; avoid touching leads

This replacement hose routes cleaning fluid to the appliance's glass-cleaning assembly so the glass receives proper spray and rinsing. Keeps the glass-clean function working and helps prevent leaks from cracked or worn tubing. What it does

• Channels water/cleaning solution between the pump and the glass-cleaning nozzle or manifold.
• Restores proper spray pattern when worn, clogged, or split hoses cause poor glass cleaning.
• Helps prevent leaks and pooling by maintaining a secure path for fluid flow.
• Works with the appliance's existing clamps and fittings to ensure a sealed connection.

• One replacement hose.

• Turn off power and shut off the water supply before starting any repair.
• Inspect hose ends and clamps; reuse OEM clamps if in good condition or replace with equivalent.
• Route the hose along the original path to avoid kinks and abrasion; secure to prevent contact with moving parts.

A replacement 10-16 shoulder screw (Type A) used to secure appliance components where a shoulder/clearance is required. Restores proper alignment and fastening for panels, brackets, or assemblies that use a shoulder-style fastener. What it does:

• Provides a fixed shoulder to control depth and spacing between parts
• Secures panels, brackets, or moving parts while allowing an exact clearance
• Helps prevent over-driving and protects mating parts from damage
• Commonly used where precise alignment or rotation clearance is needed

• Inspect the mating hole and threads for damage before installing
• Use the correct driver and torque—do not over-tighten to avoid stripping
• Replace with the same screw type and size to maintain proper fit and clearance
• Disconnect power and follow all safety precautions when accessing internal components

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.