Parts for Ge GFWR4805F2MC: Tub & Drain Pump Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This molded wire tie standoff provides a secure anchor point for a cable tie to hold wiring and harnesses away from moving parts and hot or sharp surfaces, helping reduce wear and electrical risk. Fits common HVAC and appliance wiring panels. What it does:

• Anchors wire ties to the appliance cabinet or chassis so harnesses stay routed and secured
• Prevents wires from rubbing on sharp edges, hot components or moving parts
• Helps stop intermittent electrical issues from loose or vibrating connections
• Reduces noise from loose wiring that can vibrate during operation

• One wire tie standoff

• Disconnect power before servicing the appliance to avoid shock or damage
• Mount in the original standoff hole or approved panel location; secure a cable tie through the top loop to hold the harness
• Use the correct fastener or snap method for your model—do not force or overtighten
• If routing or attaching multiple wires, verify clearance from heating elements and moving parts

Size: 8-18 b.

Retaining clip for washer assemblies. Secures components in place during operation. Replace if clip is broken, missing, or no longer holds parts firmly.

Fix your washer that won't heat water or complete cycles properly with this heater assembly. Direct replacement part for front-load washers.

This hex nut secures the heater assembly in place for safe, reliable operation. It replaces a missing or damaged nut so the heater mounting stays tight and stable. What it does

• Fastens the heater assembly or mounting hardware to prevent movement
• Restores a secure mechanical connection after a stripped, loose, or missing nut
• Helps maintain proper alignment of heater components during operation
• Prevents rattling or incorrect mounting that can cause wear or unsafe conditions

• One hex nut designed for the heater assembly

• Disconnect power to the appliance before starting any repair
• Replace only with the same part number and thread size; hand-start threads to avoid cross-threading
• Tighten to a snug fit—do not overtighten; use appropriate tools and torque practices

This 5/16-18 hex nut secures internal components in your washer. Replace if stripped, rusted, or missing to restore proper assembly and stability.

Replace your washer's counter weight if cracked, broken, or missing. This heavy structural component mounts to the tub to reduce vibration and noise.

Small metal flat washer for washing machines. Installs between components to distribute load and prevent wear. Replace if worn, damaged, or missing.

This hex washer-head screw is used in dishwashers to secure panels, brackets, and other hardware. Replacing a missing or corroded fastener restores a tight, stable installation and helps stop looseness or vibration during cycles.

• Fastens dishwasher panels, brackets, trim, or mounts to the cabinet/frame
• Replaces lost or stripped hardware after service or installation
• Helps address loose or rattling panels and minor misalignment
• Stainless steel construction per OEM spec for moisture-prone environments

• Disconnect power and water supply before servicing the dishwasher
• Wear gloves; sheet metal edges can be sharp
• Start threads by hand to avoid cross-threading; tighten with an appropriate driver
• Do not overtighten, especially when threading into plastic

Front section of the washer's outer tub assembly. Needed when the original is cracked, damaged, or worn from extended use. Installs around drum housing.

Replacement mounting screw for washer panels and internal components. Secures trim, brackets, and housing parts. Needed when original screws are stripped, corroded, or missing during repairs.

Watertight seal between washer tub halves. Replace if you notice leaks from the middle of the tub or during bearing repairs. Confirm fit with your model.

This genuine OEM replacement part is a tub assembly for washers. The tub assembly is the main tub where clothes are placed for washing inside the washing machine. If the washer is making more noise than usual, not spinning properly, or not washing clothes effectively, it might be time to replace the tub. Luckily, replacing this part is a relatively simple repair process.To get started, make sure the power is turned off to the washer. After the power supply has been cut, begin by removing the top panel of the washer to gain access to the interior. Locate the attachment that secures the drum and proceed to remove any screws that are attached to it. Once the screws have been unfastened, make sure to remove any hoses that might be attached to the drum. After that, take both hands and slowly lift the drum out of the washer. Set the old drum assembly to the side and proceed to insert the new one from the top of the washer. Set it on the attachment pieces and then fasten the screws that hold the tub in place. Once secured, reinstall the top panel and restore power to the appliance. This replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA appliances.

Mounts on top of the wash basket to counterweight spin cycles. Replace if cracked, leaking fluid, or broken to restore smooth operation and reduce vibration.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Seals the door opening on front-load washers to prevent leaks during wash and spin cycles. Replace if torn, cracked, or leaking. Verify fit with your model.

Secures the washer gasket in its groove to maintain a watertight seal during operation. Replace if worn or damaged to prevent leaks from a loose gasket.

Replace your washer nozzle gasket if you notice water leaks during fill cycles. This seal prevents water from escaping the nozzle connection. Verify fit with your model number.

Secures hose connections to prevent leaks in your dishwasher. Replace if water pools under the unit or connections feel loose. Confirm fit with your model.

This O-ring thermistor is a sealed temperature sensor that restores accurate temperature sensing in refrigeration circuits. It helps the control board read temperatures so the appliance can maintain proper cooling and defrost cycles. What it does:

• Senses temperature at the evaporator/area it's installed in so the control can regulate cooling
• Helps prevent overcooling or undercooling when operating correctly
• Can cause temperature-related error codes or improper defrosting when faulty
• Common symptom of failure: inconsistent temperatures or an error indicating a bad thermistor

• Disconnect power to the appliance before servicing to avoid shock or damage
• Replace with the exact part number to ensure fit and proper operation
• Handle the sensor and O-ring carefully to avoid damaging the lead or seal
• Test continuity/ resistance per the service manual

The Air Chamber is an OEM part for GE washing machines. It is a crucial component that assists in balancing loads and distributing water flow during wash cycles. Located inside the rear of the washer tub, the air chamber works with the impeller assembly to agitate clothing using a mixture of air and water.

Symptoms of a bad air chamber include:  

• Excessive noises or vibrations coming from the rear of the washer
• Improper or uneven agitation of clothes during wash cycles  
• Suds or water constantly being expelled from the rear of the machine
• Reduced washing performance overall

Causes can be cracks, leaks, or deformities developing in the plastic air chamber material over time and usage. Foreign debris buildup can also obstruct proper functioning. 

This genuine GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

Secures your washer's rubber gasket in its groove to maintain a leak-resistant seal. Replace if the clamp is fatigued, broken, or causing leaks during wash cycles.

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

The screw is an OEM replacement component for GE dishwashers. It is used to securely fasten parts inside the dishwasher tub assembly.

Causes of a damaged or defective screw usually involve wear from continuous mechanical stresses and vibration during dishwasher usage. Loose parts affect machine balance and performance.

Symptoms of a compromised screw placement include:

• Noises or abnormal sounds coming from inside the tub  
• Intermittent error codes related to moving components
• Detached or misaligned spray arms or filters
• Insecure tub fixtures that can be jarred with normal operation 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

Secures dishwasher sump to tub, maintaining seal compression to prevent leaks. Replace if corroded or weak. Confirm fit with your model number.

This guide drain hose directs defrost and condensate water from the evaporator area to the refrigerator drain, helping prevent water pooling and soft-food leaks inside the cabinet. It's a simple replacement to restore proper drainage. What it does:

• Routes defrost and condensate water to the drain pan or outlet
• Helps keep the internal drain path clear and reduces overflow risk
• Positions and secures the drain hose to prevent kinks or pinching
• Supports consistent drainage after defrost cycles

• Disconnect power to the appliance before beginning any work
• Access may require removing interior panels or rear cover depending on model
• Route the hose as shown in the service diagram and secure it in the guide to avoid kinks
• Check for proper drainage and leaks after reassembly

Fixes washer not draining or leaving standing water. Replaces worn or clogged pump that causes cycle interruptions. Moderate DIY repair effort.

This is a flexible drain hose that carries used wash water from the washer tub to the household drain or standpipe. It connects between the pump outlet and the external drain point. Replace this hose if you notice water leaking underneath or behind the washer, if it is kinked or cracked, or if the machine fails to drain properly.

This clamp secures a hose or wiring harness to keep connections tight and routing stable, helping prevent leaks, rubbing damage, and vibration noise. It's a simple replacement that restores proper retention and routing where the original clamp failed. What it does:

• Holds a hose or wiring harness in place to prevent movement and chafing
• Maintains a sealed connection at hose fittings to reduce the chance of leaks
• Keeps wiring routed away from heat or sharp edges to avoid damage
• Reduces vibration-related noise by stabilizing components

• One clamp

• Disconnect power (and water if applicable) before replacing to avoid shock or flooding
• Remove the old clamp with pliers or a screwdriver as required and fit the new clamp in the same orientation
• Ensure the clamp is seated firmly and does not pinch hoses or wires
• Inspect surrounding components and replace as needed

This hose sump is the molded drain hose elbow that routes washer drain water from the tub area to the drain/pump. It restores proper drainage routing and helps stop leaks where the tub outlet meets the drain hose. What it does

• Channels drain water from the washer tub to the drain/pump assembly
• Replaces cracked, split or hardened elbows that can cause leaks at the base of the washer
• Helps restore proper water flow so the washer can drain completely
• Fits where a molded sump/drain elbow is used between the tub outlet and drain hose

• One hose sump

• Disconnect power and shut off water before starting any repair
• Drain residual water from the tub and disconnect the old hose before removing
• Secure new sump with the existing hose clamp(s) and confirm a snug, leak-free fit
• If clamps or adjacent hoses are corroded or damaged, replace them to ensure a reliable seal

Hex head screw for washer assembly. Used to secure internal components and panels. Replace if stripped, corroded, or missing during maintenance or repair.

If water leaks around your washer's drain area or won't drain properly, you may need a new pump filter assembly. Traps debris and lint from the pump.

This pump shaft seal replaces the worn seal that keeps water inside the pump housing, helping stop leaks and restore proper pump operation. Designed for direct replacement to reduce puddling and water damage. What it does:

• Seals the connection between the pump impeller and motor shaft to prevent water leaks
• Commonly replaced when you find water under the appliance or persistent leaks from the pump area
• Helps the pump maintain proper water flow by keeping internal components dry
• Use when seal damage, cracking, or wear is visible during pump inspection

• One pump shaft seal

• Disconnect power and water supply before starting any repair
• Remove pump assembly or access cover to reach the seal
• Inspect mating surfaces and replace any damaged pump components to ensure a proper seal
• Wear gloves and eye protection; follow OEM instructions for reassembly and leak testing

Washer drain pump filter catches debris and lint to prevent clogs. Replace if washer won't drain or drains slowly. Confirm fit with your model number.

Secures the water filter in its housing and maintains a watertight seal. Replace if cracked, loose, or causing leaks. Confirm fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.