Crosley Hose Or Tube

Ordered the part got it in 2 days Read more

Replaced hose that came with the new washer with this longer one. Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

Our washer is next door the bathroom. So when, during the rinse cycle, the hose split and we found the back of the house completely flooded I initially assumed the culprit was either the toilet or the sink or possibly an interdimentional portal into a demonic netherworld of vaguely chlorine scented water. I spent the next hour mopping it all up and checking and re-checking the pipes in the bathroom with no apparent leaks. The next load of laundry left more clues as this time the flood was from... Read more

• Will not fill with water
• Leaking

SCREWED IT ONTO FAUCET Read more

REPLACED WITH YOUR MODULE. ARRIVED AS PROMISED & SAME AS OLD ONE. THANKS Read more

Removed the drain tube and put in a new drain tube. Read more

Our washing machine door boot seal was getting moldy and causing odor problems. Cleaning tablets and bleach weren't helping so it was time to be replaced. While I had the top and front off I changed all the hoses that could be collecting soap scum and mold, all other wetted parts were removed and washed. The video on the door boot seal, and inlet valve assembly were extremely helpful in understanding how these parts are removed and reassembled. Although the door boot seal is the most visible... Read more

Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly. Now we're washing again and no leaks! Read more

• Leaking

Thought leak was coming from icemaker but refrigerator was making ice just fine. had puddle on floor just below freezer door. upon closer inspection realized leak was coming from drain line. there were 2 pieces of tubing and the connector. leak was coming from where tubing goes into connector. wanted to replace it. didn't know what it was called. did live chat with someone I think was named James. he sent me diagrams and I could identify the part. once identified I ordered it. boom.... Read more

Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more

First of all, I want to say that this is not the first time that I have used AppliancePartsPros. They give you everything you need in the most simplified manner to repair your appliances at home. I ran my washer until I started to see the leak coming from underneath. After verifying that the intake hoses, drain hose and pump were not leaking, I opened up the washer from the top by unscrewing the two screws on the back brackets and lifting up and out. Because the leak was displaying at the... Read more

Replaced flow meter and control valve Read more

I replaced the drain pump and hose which had a flapper valve that wasn’t sealing properly. Easy repair. Took about 15 minutes total and my washing machine is Soooo much quieter!!! Read more

Replaced the water tube that went from the plastic tubing to the ice cube tray. Found that even though it was the same exact length as the original, there was only an extremely small gap from the end of the tube to a splash board. This may have been the root cause of my problems. Read more