Parts for Kitchenaid KFIS27CXBL2: 09 - Freezer Door Parts

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

Replacement door handle for your refrigerator. Installs on the exterior door to provide grip for opening and closing. Order when cracked or broken.

Replacement door handle for refrigerator. Installs on the exterior door panel. Order when your original handle is cracked, broken, or missing.

Threaded anchor that secures refrigerator door handles to the door panel. Replace if cracked, stripped, or missing to properly mount your handle hardware.

Seals freezer door to prevent frost buildup and air leaks. Replace when damaged, cracked, or not sealing properly. Verify fit with your model number.

Seals freezer door to prevent frost buildup and maintain temperature. Replace if torn, cracked, or causing moisture inside. Confirm fit with your model.

Seals freezer door to prevent warm air infiltration and ice buildup. Replace if you feel cold air leaking or see frost accumulation. Confirm fit with model.

Upper freezer glide that supports and guides the freezer drawer for smooth opening and closing. Replaces a worn or damaged glide to help eliminate binding, scraping, and uneven drawer movement. What it does:

• Guides and supports the upper freezer drawer for smooth travel; a failed glide often causes the drawer to stick or catch.
• Reduces metal-on-metal contact and scraping noises when opening or closing the drawer.
• Helps restore proper drawer alignment to prevent uneven gaps or rubbing against the cabinet.
• Lowers stress on adjacent components by returning consistent, even drawer movement.

• Disconnect power to the appliance before beginning any service work.
• Remove freezer contents and the drawer assembly per the manufacturer's instructions to access the glide.
• Replace the glide following the OEM diagram/steps; keep fasteners and mounting points aligned during reassembly.
• Test drawer operation after installation and adjust as needed for smooth, even travel.

Lower freezer bin for refrigerators. Installs at the bottom of the freezer compartment. Replace if cracked, broken, or missing side tabs and clips.

Mounting bracket that secures and supports refrigerator shelves or drawers. Replace if cracked, bent, or broken to restore proper alignment.

Upper freezer door bin for storing frozen items. Replaces cracked, broken, or worn bins to restore organized storage in your freezer compartment.

This right-side retainer glide is a replacement glide that supports and guides the appliance drum for smooth rotation and reduced wear. It helps restore proper drum alignment and reduces scraping or grinding noises during operation. What it does:

• Provides a low-friction surface for the drum to ride on, keeping rotation stable
• Prevents metal-on-metal contact that can cause scraping or grinding sounds
• Helps correct drum wobble or uneven spinning caused by a worn glide
• Protects the drum and housing from accelerated wear

• One right-side retainer glide

• Disconnect power (and gas, if applicable) before beginning any repair
• Access generally requires removing the front panel or drum assembly; follow the factory service manual for your model
• Inspect mating surfaces and replace any other worn glides or bearings as needed for best results
• Use proper tools and wear safety gear

Retainer bracket secures shelf supports in your refrigerator. Replace if cracked, broken, or missing to properly stabilize shelving and prevent sagging.

Supports and guides the upper freezer shelf for smooth sliding. Replace if shelf binds, sags, or tips when loaded. Confirm fit with your model number.

This headless, cup-point set screw secures a component to a shaft or hub inside your appliance. The 1/4-28 x 3/8 in size bites into the mating surface to prevent slipping, helping keep collars, pulleys, or knobs aligned and stable.

• Locks a hub, collar, or pulley to a shaft to prevent movement
• Helps maintain alignment and reduce wobble or vibration
• Replaces missing, stripped, or damaged set screws
• Common signs include components slipping on a shaft, rattling noises, or recurring loosening

• Disconnect power before servicing
• Clean threads and align with any flat on the shaft before tightening
• Start threads by hand to avoid cross-threading; tighten securely without overtightening
• Recheck tightness after a brief test run