Parts for Kitchenaid KFIS27CXBL2: 04 - Refrigerator Door Parts

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

This vertical mullion assembly is the interior trim piece that finishes and seals the refrigerator door edge, helping direct airflow and improve the door seal. It replaces worn or cracked mullion trim to restore fit and appearance. What it does:

• Provides the finished vertical trim on the refrigerator door edge and helps maintain an even door seal
• Channels cold air and helps reduce drafts that can cause temperature fluctuations
• Hides and protects the door edge and mounting hardware from wear and damage
• Restores proper door alignment where a damaged mullion causes poor sealing or visible gaps

• Disconnect power to the appliance before beginning any repair
• Remove door trim/panels per manufacturer instructions to access mullion; keep fasteners organized
• Align the mullion and engage all clips/tabs before re-securing screws or trim pieces
• If the door gasket or mounting clips are damaged, inspect and replace as needed for a complete seal

This mullion rail installs between refrigerator compartments to create a tight seal when the door closes. Replace if cracked, broken, or no longer sealing properly.

Restore a tight, even seal between your refrigerator's doors. This vertical mullion assembly flips into place to cover the center gap, helping maintain proper temperatures and reduce condensation.

• Bridges the gap between doors to create a continuous sealing surface
• Helps keep cold air in and warm air out for consistent cooling
• Aids proper door alignment and smooth closing
• Common symptoms of a failed mullion: broken or wobbly flipper, doors not closing fully or popping open, moisture/icing at the center, warming in the fresh food section

• Disconnect power before servicing and open the doors
• With the door open, release the retaining screws or tabs and lift the old mullion off the upper and lower pivots
• Position the new assembly on the pivots, secure it, and verify the flipper moves freely and seals evenly against the opposite door
• Restore power and recheck door operation and gasket contact along the full height

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

Seals refrigerator door to prevent air leaks and maintain temperature. Replace when torn, cracked, or loose. Confirm fit with your model number.

Seals refrigerator door to keep cool air in and prevent condensation. Replace if cracked, moldy, or not sealing properly. Verify fit with model number.

Replace your worn refrigerator door gasket to restore the tight seal that keeps cold air in. Easy push-in installation takes 10 minutes. Verify fit with your model.

Replacement handle for refrigerator doors. Installs on refrigerator or freezer compartments. Replace if cracked, broken, or damaged during transport.

Black handle for refrigerator doors and drawers. Replace a cracked, loose, or missing handle to restore a secure grip and refresh your appliance's look.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

White door stop that limits how far your refrigerator door swings open. Replace if broken, cracked, or missing to prevent door overextension and damage.

Limits refrigerator door travel to prevent overextension and cabinet damage. Replace if cracked, broken, or worn to restore controlled door movement.

Color: White

Color: Black

Color: Stainless

Threaded anchor that secures refrigerator door handles to the door panel. Replace if cracked, stripped, or missing to properly mount your handle hardware.

Black plastic cam that the refrigerator door rides on to open and close smoothly. Replace if cracked, worn, or broken causing door misalignment issues.

White plastic door closure cam installs at the bottom hinge of your refrigerator door. Replace if cracked, worn, or broken to restore proper alignment.

Gray door closer cam for bottom-mount refrigerators. Installs at the hinge to enable smooth closing and door stay-open function. Replace if cracked or worn.

6 - 19 x .250

Can't see ice in your dispenser? This refrigerator ice maker light assembly restores illumination to your ice bin, improving visibility and convenience.

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal

Ice maker stopped making ice or won't turn off? This ice level control board monitors bin levels to control ice production. Simple DIY repair.

This headless, cup-point set screw secures a component to a shaft or hub inside your appliance. The 1/4-28 x 3/8 in size bites into the mating surface to prevent slipping, helping keep collars, pulleys, or knobs aligned and stable.

• Locks a hub, collar, or pulley to a shaft to prevent movement
• Helps maintain alignment and reduce wobble or vibration
• Replaces missing, stripped, or damaged set screws
• Common signs include components slipping on a shaft, rattling noises, or recurring loosening

• Disconnect power before servicing
• Clean threads and align with any flat on the shaft before tightening
• Start threads by hand to avoid cross-threading; tighten securely without overtightening
• Recheck tightness after a brief test run