General Electric Dryer Screws, Nuts, Washers

Tapping screw for dryer or refrigerator assembly. Replace this fastener if cracked, stripped, or missing during panel or component installation.

This SCR 8-18 AB 1/2 is a replacement silicon controlled rectifier that restores proper power control to the appliance's control circuitry, helping the unit switch and regulate current reliably. What it does:

• Controls current flow in the appliance's power/control circuit for timed or regulated output
• Replaces a failed or intermittent SCR to stop erratic cycling, no-power, or control malfunctions
• Commonly used where electronic switching or phase control is required
• Helps restore stable operation when heating or motor circuits fail to receive proper control signals

• One SCR 8-18 AB 1/2 replacement component

• Disconnect power to the appliance before inspecting or replacing electrical components
• Observe ESD precautions and handle the SCR by its body; avoid touching leads
• Verify wiring and mounting orientation match the original part before final assembly

Secures and aligns the rear panel on your dryer. Replace this screw if the back housing is loose, missing, or stripped to restore proper panel fit.

Secures the door guide strip to your dryer frame, keeping the door aligned. Replace this nut if it's missing, stripped, or worn to restore proper fit.

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small components to the appliance frame
• Restores proper alignment and helps eliminate rattling or vibration
• Replaces missing or stripped fasteners that prevent parts from staying fixed
• Matches OEM fit for reliable fastening where the original screw was used

• One replacement screw

• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Tighten snugly but avoid overtightening to prevent thread damage
• Keep removed hardware organized so you can install replacements in the original locations

Mounting screw for dryer cabinet and panel assembly. Replaces lost, stripped, or damaged screws during repairs or part installations. 10-16B x 1.375".

Replacement nut for dryer assembly. Secures components and panels throughout your dryer. Order a new nut if the original is stripped, missing, or damaged.

Replacement mounting screw for your dryer. Secures panels, components, and internal parts. Order a new screw if the original is stripped, missing, or damaged.

A replacement dampening band that cushions the washer tub and helps reduce vibration and noise during spin cycles. Restores smoother, quieter operation when the tub is rubbing or moving excessively. What it does:

• Wraps around/under the outer tub to absorb shocks and dampen tub movement during spin
• Reduces vibration, banging, and harsh impacts that occur with worn or damaged dampeners
• Helps keep the tub centered and prevents metal-to-metal contact
• Common symptom: washer vibrates, rocks, or makes loud knocking during spin

• One dampening band

• Disconnect power and water supply before starting any repair
• Access typically requires removing the washer cabinet or top panel; follow model-specific instructions
• Inspect surrounding suspension components and mounting points for wear; replace if damaged
• After installation, run a short spin cycle with no load to reduce vibration

Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.

Mounting screw for dryer installation and assembly. Replace this hardware if stripped, missing, or damaged during dryer maintenance or repair work.

This small mounting screw secures panels and trim on compatible GE appliances, restoring a solid, vibration-free fit. Use it to replace a missing, stripped, or damaged fastener and keep parts aligned and secure. What it does:

• Fastens panels, trim, or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Restores secure attachment when threads are stripped or worn
• Helps maintain proper alignment to prevent noise and component wear

• Use the correct screwdriver size to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power or move the appliance to a safe position when accessing internal panels
• Consider a replacement clip or insert as recommended by the manufacturer