Gibson Washer Dryer Combo Valve
Genuine Frigidaire part
By: Frigidaire
Part Number: 134190200
Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
-
Will not fill with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
The washer was filling very slow especially cold water. Wayne S. • Oakland , MD • February 10, 2023
This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent...
Read more
More
$103.95
- Compare At:
-
$124.74
- You Save:
-
$20.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 134211400
The Water Valve is an OEM part for Frigidaire laundry centers. It's a part that controls the flow of hot and cold water into the washing machine. By opening and closing at the appropriate times during the wash cycle, this valve ensures that clothes are washed in the correct temperature settings, optimizing cleaning performance and fabric care.
Causes of a faulty Water Valve include mineral build-up from hard water blocking the openings, wear and tear causing leaks or malfunctions, and electrical problems such as faulty solenoids disrupting operation signals.
Symptoms of a malfunctioning Water Valve include:
- Water not entering the washing machine, leading to dry wash cycles.
- Water entering the machine too slowly, indicating a partial blockage.
- Water leaking from the valve when the machine is off, suggesting a failure to close completely.
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
This part fixes the following symptoms
-
Will not stop filling with water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Water was leaking into tub when machine was off Ronald H. • Tampa , FL • September 22, 2015
Part arrived in one day! Replaced the water valve. YouTube video for replacing water valve on Frigidaire top-loading washers was spot-on.
Read more
More
$84.74
- Compare At:
-
$101.69
- You Save:
-
$16.95
Genuine Frigidaire part
By: Frigidaire
Part Number: 131974700
This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does
- Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
- Seals the water line to prevent drips or continuous flow when the dispenser is idle.
- Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
- Works with the door dispenser plumbing—electrical/connectors remain unchanged.
What's included One dispenser valve assembly. Install notes
- Disconnect power and shut off the refrigerator water supply before starting.
- Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
- Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
- Test for leaks and proper dispensing after restoring power and water.
Do-It-Yourself Stories from Customers like You
Bad solenoids on bleach and softener dispenser Carl S. • Dieterich , IL • May 05, 2014
It is a simple fix with removing the old by disconnecting connecters to the solenoids. removing two screws, disconnect the hoses entering and leaving the dispenser. Installing it is simply a reverse of the removal. Total time was certainly less than 30 minutes.
Read more
More
$75.23
- Compare At:
-
$90.28
- You Save:
-
$15.05
Gibson washer dryer combo valve replacement parts are essential for keeping your appliance running smoothly. These parts play a crucial role in maintaining the water and airflow systems, ensuring that your washer dryer combo performs efficiently. Whether it's dealing with water intake, drainage, or even managing steam, the right valve parts can make all the difference in your Gibson washer dryer combo's functionality.
Keeping your appliance in top shape is vital for everyday convenience. Gibson washer dryer combo parts, especially OEM replacement parts, are designed to fit perfectly, guaranteeing the best quality and compatibility. This means you can trust that these parts will work seamlessly with your appliance, minimizing any potential issues and prolonging its lifespan.
By choosing high-quality replacement parts for your Gibson washer dryer combo, you ensure that the appliance remains reliable and efficient. And guess what? These parts are readily available, so you can easily find what you need to keep everything running as it should.
More