Ikea Control Board

Fix blank dispenser display or non-working ice/water controls. This refrigerator dispenser control board manages user selections. DIY install in 30 minutes.

The Frigidaire Range Control is an OEM component specifically designed for Frigidaire ranges. Located on the control panel, the range control houses all interactive buttons and knobs to operate the cooktop burners and oven. 

Causes of failure include damage from excess moisture, cracks developing from repeated tightening/loosening of knobs, or wear of electronic switches impacting responses.

Symptoms of a bad range control include:

• Unresponsive or inaccurate oven/stovetop controls  
• Inability to power on or adjust temperatures
• Faulty burners failing to ignite or flame improperly
• Loose, damaged, or missing knobs hindering the use

This OEM component is also compatible with Crosley, RV, and some Kenmore-branded ranges and ensures a straightforward repair experience.

Dishwasher won't heat, cycle, or start? A failed control board disrupts heating, wash cycles, and dispenser timing. Moderately challenging DIY repair.

Dishwasher not responding or display has no lights? This control assembly manages cycle selection and status display. Replaces worn or damaged controls.

Fix refrigerator temperature issues, display failures, or defrost problems. This control board manages cooling cycles and temperature settings.

Fix temperature fluctuations, defrost issues, or complete control failure with this refrigerator electronic control board. Moderately challenging repair.

Microwave not heating or showing F1 E5 error? This inverter board converts voltage to power the magnetron. Requires tech sheet for testing procedures.

This electronic control board is the central module that runs your dishwasher's cycles. It controls power and timing so the unit fills, washes, drains, and dries correctly—restoring normal operation when the original board has failed.

• Manages cycle timing and options, routing power to the wash motor, drain pump, water inlet valve, and heating circuit
• Interfaces with sensors and the door latch to start and advance cycles
• Monitors faults to help protect components and ensure proper operation

• Disconnect power at the breaker and verify no voltage before service
• Access location varies by model
• Use ESD precautions; move connectors one at a time to the matching terminals
• After reassembly, run the unit's diagnostic/service cycle per the tech sheet to verify operation

Range won't turn off or functions stay powered on? This relay board controls electrical flow to range components. Common fix for stuck-on appliances.

Fix a refrigerator that won't cool, turn on after defrost, or shows error codes. This electronic control board manages power and timing for all functions.

Fix a dishwasher that won't start, shows error codes, or has unresponsive controls. This main control board manages cycles and user interface functions.

If your dishwasher won't start, cycles won't advance, or buttons don't respond, the control board may have failed. This board regulates all functions.

If your oven control flickers or resets randomly, the transient suppressor may have failed. This part protects the control board from power surges.

Fix a dishwasher that won't start, shows no lights, or runs cycles too long. Electronic control board manages all dishwasher functions. Moderate difficulty repair.

Fixes refrigerator not cooling, compressor not running, or frost buildup. This control board manages cooling cycles and temperature regulation.

This Electronic Control Board is the appliance's central control module. It interprets inputs from sensors and switches and directs power to motors, valves, heaters, and fans to run cycles reliably when the original board has failed.

• Manages overall operation by processing signals and executing programmed cycles
• Sends power/commands to components such as motors, pumps, fans, heaters, and valves
• Typical symptoms of a failed board: no power or won't start, unresponsive controls, cycles that won't advance, intermittent shutdowns, or error codes
• Useful when diagnostics point to control failure after ruling out fuses, switches, sensors, and wiring

• Disconnect power before servicing; turn off water supply if applicable
• Use ESD protection and handle the board by its edges
• Photograph/label all connectors; move harnesses one at a time and transfer any jumpers/settings from the old board if present
• Mount securely, reconnect wiring, reassemble, then run the unit's diagnostic/self-test per the service manual