Jenn-Air Dishwasher Parts

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more

I ordered 4 of this part from AppliancePartsPros.com and watched the repair video of the product. This was a simple repair that took 10 minutes to replace all 4 wheel units on the bottom rack. Product is exact match to the part I replaced. Read more

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

Installed 2 new dishrack roller assemblies. The only tools I needed were my fingers, snapped the old assemblies out and snapped the assemblies in. Read more

I replaced the adjusters on both sides (since two rollers broke off on one and one broke off on the other). Replacement was easy, just remember to keep the clips from the original adjusters. Take the clips off, remove the adjuster, replace with the new adjuster, and replace the clips. The new adjuster comes with the rollers already attached so no need to keep the ones from when plastic axle broke on the original adjusters. Read more

My Whirlpool dishwasher was leaking out the bottom of the door. I replaced the gasket and the lower door seal. When I ran a test wash, it was still leaking. After reading more online, I found that it could be a cracked washer arm. The initial inspection of the washer arm looked normal but when I used my faucet to slowly pour water into the inlet of the arm, I noted that water was leaking through a seam and not just the holes where it should come out. I then tried running a wash without the... Read more

Thanks to Jason and his tech people at Appliance Parts Pro, I was able to remove and replace the seal and eliminate all leaks at the bottom of the door. I have a Kitchenaide (Whirlpool) dishwasher model KUDC10IXBL1. Here is how to replace the bottom door seal. 1) Shut off breaker to dishwasher on the electrical panel. 2) Open the dishwasher door completely, and while supporting the door, remove the hex head screws that hold the outside cover. 2) Close the door carefully and slip the outside... Read more

I took the bottom access cover off, and checked underneath the unit to isolate where it was leaking from. Cleaned the cover, and the spot where the leak happened was marked for me. The front, far left hand side, behind the door. Ran a quick rinse cycle with a pan under the spot to verify it was there. It was. Then I did an internet search and found your website. Our dishwasher, bought in November of 2016, was listed, and several of the reviewers said wonderful things about their experiences... Read more

• Noisy
• Door won't close
• Door latch failure

I finally decided to repair my dishwasher because the door would free fall to the floor possibly breaking the hinges. Also the top shelf was rolling out on its own every time the door was opened. I first pulled the dishwasher out of the enclosure and found that the drain hose was directly under the pump area throwing the unit completely out of level. Also the inadequate plastic and rope counterbalance on the left side was completely broken where the rope was attached to the plastic piece to the... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

Replaced wheel assembly because prongs were broken and replaced track because wheel assemblies were rolling out from the track when extended. Read more

The part went on easily. U Tube video answered any questions I had before installing. Read more

Ordered a new one. It took about 10 seconds to install. Now it’s like brand new. Read more

• Will not fill with water

As mentioned, our Whirlpool Dishwasher would complete the cycle but Tablet pretty much sat in the Soap Dispenser Box nor there was any sign of water inside the Dishwasher. This happened 2 - 3 times. Hence decided to dive into what the fix was. After reviewing a bunch of Youtube Videos, understood first how a typical Dishwasher operates and what are the basic checks it does before water is let inside. So it typically first checks whether Door S/w got activated, followed by Float Switch... Read more

• Not drying dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more