Kenmore / Sears Washer Dispenser Parts

Fix fabric softener not dispensing or leaking onto clothes. This top-load washer dispenser snaps onto the agitator in minutes. Easy DIY replacement.

Fix water leaking from your detergent drawer. This dispenser holds and releases detergent, softener, and bleach at the right time. Easy DIY repair.

Fix a broken or missing detergent dispenser cover that's cracked or won't guide proper detergent placement. Simple 5-minute replacement repair.

Fix a leaking or broken dispenser drawer that won't release detergent or fabric softener properly. Direct replacement restores proper dispensing.

Fix detergent not dispensing or drawer leaking issues with this washer dispenser drawer assembly. Holds detergent and fabric softener during wash cycles.

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

This dispenser assembly replaces a worn or damaged refrigerator dispenser to restore reliable dispensing of water and ice. It provides the dispenser housing and interface needed for proper user operation and sealing at the door. What it does:

• Houses the dispenser components and provides the push-lever/door opening for water and ice delivery
• Restores a broken, cracked or loose dispenser opening that causes poor engagement or cosmetic damage
• Helps stop minor leaks or drips at the dispenser area when seals and gaskets are intact
• Eliminates sticking or misaligned dispenser operation that prevents normal dispensing

• Disconnect power and shut off the water supply before beginning any work.
• Installation typically requires removing the refrigerator door panel(s) and detaching the old dispenser from the inner door; keep fasteners for reuse unless replacements are provided.
• Handle plastic parts gently to avoid cracking; inspect door seals and gaskets and replace if worn.
• After installation, restore power and water, then test dispenser operation and check for leaks.

Fix exposed fasteners or openings on your washer dispenser with this protective cover cap. Keeps dirt and moisture out while restoring a clean finish.

Fix detergent not dispensing or leaking from the drawer. This washer dispenser assembly replaces cracked or clogged units. Direct-fit installation.

Fix detergent not dispensing or drawer stuck issues with this washer dispenser. Simple DIY fix for soap buildup and dispensing problems.

Fix loose or missing dispenser trim with this washer cover cap. Snaps into place to protect fastener openings and restore a clean, finished look. Easy DIY fix.

Detergent or softener not dispensing properly? This dispenser drawer assembly deposits detergent at the right time. Straightforward replacement.

Fix detergent not dispensing or leaking from the top of your washer. This drawer holds detergent and additives. Takes 30-40 minutes to replace.

This dispenser assembly mounts in the refrigerator door to provide a stable dispensing point for ice and water and restore normal use of the door dispenser. It replaces damaged or worn dispenser components to stop leaks and restore proper operation. What it does:

• Provides the exterior opening and actuator area for dispensing ice and/or water
• Guides and supports the dispense lever or actuator and related components
• Helps prevent leaks and dripping from the door dispense area
• Commonly replaced when the dispenser won't actuate, leaks, or has broken trim or lever

• Disconnect power and shut off the water supply before starting
• Door panel or inner liner removal may be required for access
• Handle trim and plastic parts carefully to avoid cracking during removal/installation
• Follow the refrigerator's service manual or tech sheet for torque and routing details

This dispenser is the exterior door component that delivers chilled water and/or ice from the refrigerator, restoring normal dispensing and preventing drips or jams. It replaces a damaged, cracked or non-functioning door dispenser. What it does

• Guides water and ice from the internal plumbing to the exterior spout so items can be dispensed from the door.
• Re-establishes a secure spout and actuator for reliable dispensing and reduced leaks.
• Stops common dispenser symptoms such as leaking at the door, stuck or loose dispenser lever, and misaligned spout.
• Helps restore normal dispensing when the door dispenser is cracked, broken, or no longer seating properly.

• One dispenser assembly.

• Disconnect power and shut off the refrigerator water supply before beginning.
• Remove the interior door panel and any trim to access the dispenser assembly; keep fasteners organized for reassembly.
• Inspect and replace any worn gaskets or seals to prevent leaks; ensure proper hose routing.
• Test operation and check for leaks after reconnecting power and water.

Leaking detergent or clogged dispenser? Replace the drawer housing to restore proper detergent flow and eliminate leaks. Straightforward DIY fix.