Kitchenaid Spring Parts

When I removed the cabinet, all of the springs appeared in tact, I had already replaced the counter balance spring so I knew that was not the issue. None of the suspension springs or brackets were broken but they did look worn/rusty so I replaced all of the brackets (2 in front and 1 large in back), all of the suspension spring retainers, and all of the suspension springs and it fixed the issue! I plan to also replace the Self leveling leg spring which is an easy fix since it's on the back of... Read more

• Shakes and moves

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more

Replace the drum drive belt and tension pulley assy. Read more

I called a local repair center who estimated $300+ to fix this. I bought a door handle and door latch for $~100 and fixed my dishwasher in about 10 mins. I ordered the parts on Sunday, they arrived on Tuesday. Very happy with appliance parts pros and would recommend them. Read more

My wife and I along with Mat on the video replaced the upper and lower friction pads, along with the balance springs. The machine runs smooth as it did new. Thank you everyone at Appliance Parts Pro and Mat. You are a great company. P.S. my wife and I should had made our own video for you since we are both in our 60s I bet it would have been funny Thanks Again. JIm & Debbie from Texas. Read more

Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine). If you replace the springs, be sure to check for the spring bracket mount. You will also need those. The washer is running fine. Next I'll work on the dryer. Read more

Followed instruction I saw on a you-tube video. Was quick and easy. Read more

Checked switch with a voltmeter, determined the switch was bad. Ordered a new switch....watched a short how to you-tube video.....and from there.....it was fixed. Read more

A shout out to A.P.P.: Quality parts always come quickly and are what I ordered. No, they are not always the cheapest nor do they have all parts for everything (who does?) but their website is the easiest to use and cost differences are usually slight. I have found A.P.P. trustworthy and reliable for the ten or so purchases I've made. This repair process requires that the DW be completely free from cabinet sidewalls. For me that meant pulling the DW from its installed undercounter space. I... Read more

Found the broken parts upon disassembly. Ordered new parts. Parts were shipped very quickly. Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

One was broke I replaced both to make them the same again. Read more

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

Took out the old and broken and replaced with new springs... Read more

Replaced the part. Read more