Parts for Ge PS950SF3SS: Lower Door Parts

Decorative badge emblem that mounts on range control panel or door. Restores appliance exterior appearance when original is faded, scratched, or missing.

Insulation pad that installs behind the oven inner door liner to retain heat. Replace if worn, damaged, water-logged, or missing to restore proper insulation.

Thermal insulation that fits between inner and outer oven door panels along the side edge. Replace when burnt, brittle, cracked, or missing from wear.

The Oven Door Gasket is an OEM part for GE ranges. This gasket is responsible for creating an air-tight seal between the door and the oven housing. It allows heat to be properly contained within the oven cavity during the cooking process. 

Causes of a bad gasket can include warping, cracking, or breakdown of the gasket material over repeated heating and cooling cycles. Exposure to excessive heat or impact damage is also possible. 

Symptoms of a bad gasket include:

• Inability to maintain proper oven temperatures 
• Leaks of heat, smoke, or flames from the door seal area
• Drafts or cold spots felt around the door perimeter
• Difficulty in fully latching the oven door closed

This OEM GE replacement gasket is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures insulation inside the oven door to prevent shifting and maintain heat containment. Replace if clip is cracked, broken, or missing.

Secures and holds the glass panel in place on your oven door. Replace this retainer if it's cracked, broken, or missing to properly support the glass.

Retainer holds the glass panel securely in your oven door. Replace if cracked, broken, or missing to restore proper glass mounting and door appearance.

Lower door panel assembly for ranges. Installs on the front lower oven door section. Replace if cracked, dented, discolored, or damaged from impact.

Replacement inner glass pane for oven doors. Installs inside door assembly to restore visibility and heat containment. Replaces cracked, broken, or fogged glass.

The Handle and End Cap Assembly is an OEM part for GE ovens. This assembly comprises the handle used to open and close the oven door, along with the end caps that secure the handle firmly in place. The handle measures 27.5 inches long

Over time, the handle and end caps can become worn or damaged due to frequent use, exposure to high temperatures, or accidental impact. Such issues can make it challenging to operate the oven door properly and safely.

Symptoms of a bad Handle and End Cap Assembly include:

• Difficulty in opening or closing the oven door
• A loose or wobbly handle
• Visible cracks or damage to the handle or end caps
• The handle detaching from the oven door

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This spacer bracket is the factory replacement part that positions and secures a range or oven handle, keeping the handle aligned and spaced correctly for a snug fit and normal operation. What it does

• Holds the handle at the correct distance from the door or control panel so the handle sits straight and evenly
• Prevents handle wobble or rotation by supporting the mounting hardware
• Helps close gaps between the handle and appliance surface for a finished appearance
• Common symptom: loose, tilted, or wobbly handle or visible gap at the handle mounting

• Disconnect power to the appliance (unplug or turn off the circuit breaker) before starting any repair
• Use basic hand tools (screwdriver/socket) to remove the handle and fasteners, replace the bracket, then reassemble
• Keep small screws and fasteners organized during removal; replace any damaged fasteners
• Do not overtighten screws — snug is sufficient to avoid stripping or cracking the bracket

Inner glass assembly for oven doors. Replace when cracked, shattered, or broken to restore door visibility and insulation. Verify fit with your model number.

Hex head machine screw with 10-32 thread, 1-3/4 inches long. Secures brackets, panels, and internal oven components. Replace missing or stripped screws.

ST10-16 X 7/16"

Mounting screw secures range components and panels. Replace if screw is stripped, missing, or damaged during appliance repair or maintenance work.