Maytag Parts

Placed the robber seal Read more

After ignoring for a couple of years that the bearings were bad on our Whirlpool Cabrio washer and just closing the door to the laundry room, it started slinging grease underneath during the spin cycle. Knowing that the cost to call out a repairman would be close to the cost of a new washer, I decided that it would be a nice Saturday project after reviewing AppliancePartsPros’ repair video. The bearing & tub seal kit and bearing installation tool arrived in two days. I’ve done a lot of... Read more

I tried to hire someone through Home Advisor and was given an initial estimate of 436.00!?! However, no one ever contacted me about repairing the dryer. The washer and dryer are about 12 or 13 years old, so me and the wife discussed going to look at the alternative.... Buying a new washer and dryer set. We had planned on going on Dec 10th. I then decided to do some research on YouTube on Dec 8th for dryer repair and came across a video that was made by AppliancePartsPros.com. The video covered... Read more

My wife and I along with Mat on the video replaced the upper and lower friction pads, along with the balance springs. The machine runs smooth as it did new. Thank you everyone at Appliance Parts Pro and Mat. You are a great company. P.S. my wife and I should had made our own video for you since we are both in our 60s I bet it would have been funny Thanks Again. JIm & Debbie from Texas. Read more

Replaced screen. Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

• Marks left on clothes

After replacing thermal fuse once and having it fail a second time, I had to dig a little deeper to uncover the problem. I checked for blockage in the vent but everything was clear. I did, however, find that the drum had some up and down play in it. After closer inspection, I could see that the front drum seal was actually worn to the point that I could see a gap between the seal and the drum. I figured that the gap in the seal was letting air in and not letting sufficient air flow through the... Read more

Removed valve and replaced with new one. Read more

Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more

I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more

Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine). If you replace the springs, be sure to check for the spring bracket mount. You will also need those. The washer is running fine. Next I'll work on the dryer. Read more

I ordered 1 assembly first and then another broke. so I ordered 2 more and replaced 2 more. The 4th was replaced last summer. I should have ordered 4 and replaced all when the 1st one failed. Read more

$4 part and a little time saved $250 if I had had to replace the whole plug-in duel burner unit for our Jenn-Air range. Spade that was replaced fed both burners, other two spades just one. If your burners do not turn on, check the spades before you replace the coils. Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Replaced the water valve. Easy repair. The repair video was spot-on. Tools needed: Slip joint pliers for removing and attaching the hoses and moving the hose clip. 5/16 nut driver. Phone to take a picture so I could get the wires put back right. Shut off the water and unplug from power. Remove the hoses. Using a 5/16 nut driver remove the single screw that holds the bracket, lift bracket slightly and pull from the washer. There is a little slack in wires and fill hose to work with. Take a... Read more

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

Changed parts Read more